Can You Use Mold Armor on Grout?
On this page
- What Mold Armor is
- What the Mold Armor label says about grout
- Sealed or unsealed: what the label covers
- What is in the bottle: the safety data sheet
- How strong is Mold Armor next to the grout?
- Can you use Mold Armor on colored grout?
- Should you use the weekly prevention spray on grout?
- A worked case: one bathroom, two grouts
- Grout by grout: where the makers draw the lines
- Mold Armor or not: grout by grout
- How to use Mold Armor on grout
- Mold Armor, Tilex, RMR-86 or Clorox bleach?
- Where this answer stops applying
- Frequently asked questions
- Sources and standards
Yes on sealed grout, because the Mold Armor label names it. Mold Armor Mold & Mildew Killer + Quick Stain Remover is a bleach spray, and its bottle lists "sealed grout" among the hard, non-porous surfaces it is made for. Unsealed grout is not on that list, so the label's mold kill claim does not reach bare grout. The stain step is the same either way: spray, wait 10 minutes for the stains to go, then rinse. On colored grout, test a hidden joint first, since this is the strongest bleach of the common grout sprays.
Key takeaways
- Mold Armor Mold & Mildew Killer + Quick Stain Remover (FG502) is 4.0 percent sodium hypochlorite, the chemical in chlorine bleach, plus 1.0 percent sodium carbonate. It is registered with EPA as Reg. No. 4091-23.
- The bottle's surface list names "sealed grout," not grout. Every EPA version of the label since 2017 draws the same line.
- The kill claim is 60 seconds on hard, non-porous surfaces. EPA treats plain grout as porous, so on unsealed grout Mold Armor is a stain remover, not a registered mold killer.
- To remove stains: apply, wait 10 minutes, rinse. Rinse vinyl or rubber within 15 minutes. Keep it off metal, and never mix it with acids or ammonia.
- On colored grout, test a hidden joint first, or use oxygen bleach. Keep it off recolored grout and stone, and use it only now and then on sealed grout, since sealer makers ban bleach as a routine.
What Mold Armor is
Mold Armor is a brand of mold and mildew products made for W.M. Barr of Memphis, Tennessee. The one most people mean is the white trigger spray: Mold Armor Mold & Mildew Killer + Quick Stain Remover, product code FG502. That is the product this page rules on.
Its working part is sodium hypochlorite, the chemical in household chlorine bleach. Bleach is an oxidizer. It breaks down the colored parts of mold and mildew, so dark spots turn pale or vanish. The label lists 4.0 percent sodium hypochlorite and 1.0 percent sodium carbonate, a mild alkali.
Four more terms decide the answer.
- Kill claim. In the US, a product that says it kills mold is a pesticide, so EPA must accept every claim on its label, and the label says on which surfaces each claim holds. A product can only promise to kill mold where its label says so.
- Hard, non-porous surface. A surface that liquid cannot soak into, like glazed tile, glass or chrome. A porous surface has tiny holes that soak up water and whatever is in it.
- Unsealed cement grout. The common sanded or unsanded grout mixed with water and left bare, which makes it porous. In 2005, when Clorox asked to list grout on a bleach sanitizer spray, EPA struck it and wrote: "Grout is a porous surface."
- Sealed grout. Cement grout coated with a grout sealer, which fills or lines its pores so water beads up. Mold Armor's label puts sealed grout in its list of hard, non-porous surfaces.
So the question is not whether bleach works on grout. It does, and bleach on grout covers the general case, so the question here is what the Mold Armor label covers, and that turns on whether the grout is sealed.
What the Mold Armor label says about grout
EPA files Mold Armor under the name Mold Armor Formula 400, Reg. No. 4091-23. EPA lists FG502's name, "Mold Armor Mold & Mildew Killer + Quick Stain Remover," as one of more than 30 brand names sold under that one registration. EPA first registered it on October 2, 2017, and has accepted new versions of the label in March 2018, December 2019 and April 2023.
The printed FG502 bottle (copyright 2018) opens its directions with a surface list: "For use on hard, non-porous surfaces, bathtubs, shower doors, toilet seats, countertops, sinks, sealed grout, vinyl, garbage cans, plastic surfaces, sealed fiberglass, sealed granite, glazed porcelain tile, glazed ceramic tile, laminate, Formica and linoleum." Grout appears once in that list, and only as "sealed grout."
The bottle then gives four sets of directions.
- Sanitize hard, nonporous surfaces: spray from 6 to 8 inches until wet, let stand 10 seconds, wipe.
- Disinfect hard, non-porous surfaces: let stand 30 seconds. "To kill mold and mildew, let stand 60 seconds. Then rinse with water or wipe with a cloth."
- Prevent growth on hard surfaces: "Thoroughly wet surface. Allow to air dry. Repeat every 7 days."
- Remove stains: "Apply to stains. No scrubbing required. Wait 10 minutes for stains to disappear, then rinse with water or wipe with a damp sponge. Rinse vinyl or rubber surfaces within 15 minutes as prolonged contact may cause damage."
The bottle also says, "Test on a small inconspicuous area before applying to surface." It warns that "Prolonged contact with metal may cause pitting or discoloration," and that contact with clothing, carpet, fabric, painted wood or paper "may cause discoloration or damage." It says to open windows and turn on a fan before use.
The EPA master label holds every claim Barr may print, and it draws the same line. Its tables of hard, non-porous surfaces list "Sealed grout." Its kill claims name "sealed tile grout" and "tile, sealed grout, tubs, shower doors." Two other claims name grout without the word sealed. One is a cleaning claim: "Easily removes tough mold stains from grout." The other is a growth-prevention claim: "Prevents mildew growth on tile grout, caulking, and corners." Neither is a kill claim, and all four versions on EPA's file, from 2017 to 2023, carry the same wording on grout.
Sealed or unsealed: what the label covers
This is the question the label settles, and it is why two answers circulate: one says Mold Armor kills mold on grout, which is true of sealed grout. The other says it is fine on any grout, which is true of the stain removal and not of the kill claim.
On sealed grout, every claim on the bottle applies. Sealed grout is on the list of hard, non-porous surfaces, so the 60-second kill time and the 10-minute stain step both reach it.
On unsealed grout, the kill claim does not apply. The label's kill directions are for hard, non-porous surfaces, and bare grout is porous by EPA's own ruling. Tilex shows how EPA handles a porous surface: in April 2003, EPA split the Tilex label in two: 5 minutes for glazed tile, and a separate line for grout, "TO KILL MOLD & MILDEW ON HARD, POROUS SURFACES such as grout and cement," at 10 minutes. Mold Armor's label has no porous line like that anywhere in its four versions.
So here is the ruling: on bare grout, treat Mold Armor as a stain remover. The bleach will still lift the color, and EPA accepted the cleaning claim "Easily removes tough mold stains from grout." But its 60-second kill time is not proven for bare grout. If you want a registered kill claim on unsealed grout, Tilex has one, at 10 minutes.
Not sure if your grout is sealed? A few drops of water will tell you, because if they bead up the sealer is working, and if they soak in and darken the joint within a few minutes, treat it as unsealed. The water drop test page shows how to read it.
What is in the bottle: the safety data sheet
A safety data sheet (SDS) is the maker's legal record of a product. Section 3 lists the hazardous ingredients and Section 9 gives the pH. W.M. Barr's sheet for FG502 is revision April 7, 2021, and it covers five product codes: FG502, FG502AM, FG502AMBLK, FG502BLK and FG502W.
- Ingredients: sodium hypochlorite 1.0 to 5.0 percent, and sodium hydroxide (lye) 0.1 to 1.0 percent.
- pH: 12 to 13.5.
- Hazards: signal word Warning; skin irritation Category 2 and serious eye irritation Category 2A. Barr asks for rubber or neoprene gloves and eye protection.
- Air: "Open all windows and doors. Use only with a cross ventilation of moving fresh air across the work area." If you notice a strong odor, dizziness, headache, nausea or watery eyes, "Stop," since ventilation is inadequate.
- Mixing: "Do not mix with acids, ammonia, or other household chemicals as dangerous fumes may result."
The sheet gives the intended use as "Mold and Mildew Stain Remover." The label's 4.0 percent sits inside the sheet's 1 to 5 percent range.
How strong is Mold Armor next to the grout?
On the pH scale, 7 is neutral, below 7 is acid, like vinegar, and above 7 is alkaline, like ammonia or lye, and each whole step is ten times stronger than the one before.
Cement grout is alkaline too: MAPEI's sheet for Keracolor S sanded grout (version 10, March 26, 2026) gives pH 11.00 at a 10 percent mix in water. Mold Armor at 12 to 13.5 is 10 to about 316 times as alkaline as that. Tilex, at 12.4 to 12.8, sits inside the same band.
An alkali does not dissolve cement the way acid does, so the risk from Mold Armor is to what sits on the cement: the pigment, the sealer and any colorant. On bleach strength, 4.0 percent is the highest of the common grout sprays. Tilex is 2.4 percent on its label, so Mold Armor carries about two thirds more bleach. The grout cleaner pH chart places it beside the other bathroom cleaners.
Can you use Mold Armor on colored grout?
Barr does not say, since neither the bottle nor the sheet mentions grout color, and no grout maker has published a fade test for Mold Armor. The bottle's only word on it is general: "Test on a small inconspicuous area before applying to surface." What the makers say about bleach points one way.
- A grout maker. TEC's Power Grout care bulletin (November 2025): "Do not use vinegar, bleach, ammonia or other general purpose cleaning products ... Using these routinely can degrade the grout." The key word is "routinely."
- A cleaner maker. Simple Green's grout page: "chlorine bleach will leach color out of tinted grout."
- A sealer maker. Aqua Mix Sealer's Choice Gold (TDS-158): "Do not use cleaners containing ammonia, acids or bleach."
- A colorant maker. Aqua Mix Grout Colorant (TDS-173): "high-alkaline, acidic or solvent-based cleaners will affect wear."
Two facts make Mold Armor the case to be most careful with. It carries more bleach than Tilex, and its stain step sits for 10 minutes, not 15 seconds like RMR-86.
So here is the ruling: on colored grout, Mold Armor is a spot tool for a stain nothing gentler will shift. Test a hidden joint first, cover the whole area evenly so no patch gets a longer dose, and rinse it all at once. For routine stain work on color, start with oxygen bleach: OxiClean on grout covers how. If the color has already gone patchy, see fading grout.
Should you use the weekly prevention spray on grout?
The label offers a growth-prevention step: wet the surface, let it air dry, and repeat every 7 days. That step says "hard surfaces," not hard, non-porous ones, and the master label allows the claim "Prevents mildew growth on tile grout."
On grout, skip it, because bleach left to dry in a joint every week is exactly the routine use TEC warns against. It also goes against Aqua Mix's no-bleach rule on sealed grout and its rule on high-alkaline cleaners for colorant. Mold grows back where grout stays damp, so dry the shower instead. Grout mold and mildew covers how to tell surface mildew from a moisture problem.
A worked case: one bathroom, two grouts
Take a common bathroom. The tub surround is white glazed tile with white cement grout, sealed two years ago. The floor is porcelain tile with tan cement grout that was never sealed. Black mildew spots sit along the bottom row of wall joints and in the floor corners by the tub. There is a chrome tub spout and a vinyl shower curtain.
Start with a water drop test on the wall grout. Suppose the drops still bead up. Then the grout counts as sealed, and the full label applies, so open a window, run the fan, and rinse off any other cleaner first. Spray the stained joints, wait 10 minutes for the stains to go, and rinse with clean water. The 60-second kill time is inside that 10 minutes, so one application does both jobs.
Now the sealer. Aqua Mix says no bleach on its sealed grout, so this is a one-off treatment, not a weekly one. A day later, test the joints again, and if the drops now soak in, the bleach has worn the sealer, and the joints need resealing. How often to seal grout covers that.
Then the tan floor grout. It is bare, so the kill claim does not reach it, and it is colored, so test first. Pick a joint behind the door, spray it, wait 10 minutes, rinse, and let it dry overnight. Grout looks darker when wet, so judge it only once it is dry. If it matches, treat the floor corners the same way, covering every joint in the area and rinsing it all at once. If the test joint came up lighter, stop and use oxygen bleach.
Last come the metal and vinyl: wipe any spray off the chrome spout at once, since the label warns of pitting, and rinse the curtain within 15 minutes or move it out of the way first.
Change one fact and the answer shifts. If the floor grout were white, the color test drops out, but it is still a stain step only on bare grout, and if it were recolored, you would skip Mold Armor on it.
Grout by grout: where the makers draw the lines
Sealed cement grout. On the label, so every claim applies: 60 seconds to kill mold, 10 minutes for stains, then rinse. But Aqua Mix says no bleach on its sealer, so use it as a spot treatment, not a routine, and run a water drop test afterward.
White or light cement grout, unsealed. Yes as a stain remover: 10 minutes, then rinse. The kill claim does not cover it, so for a registered kill on bare grout, use Tilex at 10 minutes.
Colored cement grout. Spot use only, after a hidden test. TEC bans bleach as a routine cleaner and Simple Green says it leaches color, so reach for oxygen bleach first.
Recolored grout. Keep it off, since TDS-173 says high-alkaline cleaners affect colorant wear, and Mold Armor's pH is 12 to 13.5. See grout colorant.
Epoxy grout. Yes for a short, rinsed spot clean. LATICRETE's chart for SPECTRALOCK PRO Premium (DS-681.0-0217) rates 5 percent sodium hypochlorite "R," recommended, at 30 minutes and 24 hours, and "NR," not recommended, at 7 days. Mold Armor is 4.0 percent, under what the chart tested, and you rinse it off after 10 minutes. More in cleaning epoxy grout.
Natural stone tile. The bottle names "sealed granite" and no other stone, so marble, limestone and travertine are not covered. See grout for natural stone.
Joints beside metal, vinyl or rubber. Keep spray off metal, since the label warns of pitting and discoloration, and rinse vinyl and rubber within 15 minutes. Grout or caulk at metal trim covers those joints.
Mold Armor or not: grout by grout
| Grout and job | Use Mold Armor? | Why |
|---|---|---|
| Sealed cement grout, mildew | Yes, as a spot treatment: 60 s to kill, 10 min for stains, rinse; water drop test after | Bottle: "sealed grout" among hard, non-porous surfaces; Aqua Mix TDS-158: no bleach on sealer |
| White or light cement grout, unsealed | Stain removal only: 10 min, rinse | Kill claim is hard, non-porous only; EPA: "Grout is a porous surface"; master label: "removes tough mold stains from grout" |
| Colored cement grout | Spot use after a hidden-joint test; oxygen bleach first | Bottle: test a small area; TEC: no bleach "routinely"; Simple Green: bleach leaches color |
| Recolored grout (colorant) | No | Aqua Mix TDS-173: high-alkaline cleaners "will affect wear"; SDS pH 12-13.5 |
| Epoxy grout | Yes for spots, rinsed | LATICRETE DS-681.0-0217: 5% hypochlorite R at 24 h, NR at 7 days; Mold Armor 4.0% |
| Natural stone tile | Sealed granite only | Bottle names "sealed granite," no other stone |
| Weekly prevention spray on grout | Skip it; dry the shower instead | TEC: routine bleach degrades grout; TDS-158 and TDS-173 |
| Joints beside metal, vinyl or rubber | Keep off metal; rinse vinyl and rubber within 15 min | Bottle: "pitting or discoloration" on metal; vinyl and rubber 15-minute rule |
Bottom line: Mold Armor's label clears sealed grout, not grout in general. On sealed grout, spray, wait 10 minutes for stains (60 seconds kills mold), and rinse, but not as a weekly habit, since sealer makers ban routine bleach. On unsealed grout, it removes stains but its kill claim does not apply, so use Tilex if you want a registered kill there. Test colored grout first, and keep it off recolored grout, stone other than sealed granite, and metal.
How to use Mold Armor on grout
- Check the grout. Run a water drop test first. Sealed: the full label applies. Unsealed: it is a stain remover only. Colored: test a hidden joint. Recolored or stone other than sealed granite: stop.
- Rinse off other cleaners with clean water first, above all any acid, vinegar, ammonia or toilet bowl cleaner.
- Get air moving and cover up. Open windows and doors and turn on the fan. Wear rubber or neoprene gloves and eye protection, as Barr's sheet asks.
- Turn the nozzle to ON and spray from 6 to 8 inches until the stained joints are wet. Keep it off metal, and move vinyl or rubber items out of the way.
- Wait 10 minutes for the stains to disappear. No scrubbing is needed, the label says.
- Rinse with clean water or wipe with a damp sponge. Grout is porous, so rinse it well rather than let bleach dry in the joints. Grout porosity and absorption explains why.
- Retest sealed grout the next day with a few drops of water, and reseal if they soak in.
- Dry the shower after every use, since moisture is what brings mildew back.
Mold Armor, Tilex, RMR-86 or Clorox bleach?
All four are chlorine bleach, and the difference is what the label promises on grout.
Tilex Mold & Mildew Remover (EPA 5813-24) is 2.4 percent on its label. It is the one with a kill line for bare grout: "hard, porous surfaces such as grout and cement," 10 minutes, then rinse. Its 2024 surface table also lists "Sealed Grout," and its stain step is "Spray, wait until stains disappear and rinse." Clorox's Canadian sheet gives pH 12.4 to 12.8.
RMR-86 has no EPA registration, so it makes no kill claim at all, and its June 2026 sheet lists 1 to 5 percent bleach and pH 11.37. RMR's own pages name "grout lines," and the directions are spray, wait at least 15 seconds, rinse.
Clorox's own grout guide uses plain bleach: "mix 1 gallon of water with 1/3 cup of Clorox Disinfecting Bleach," brush it on, let it sit 10 minutes, scrub, and rinse. The guide calls it a way to "remove mold stains," and says the dilution is for "hard, nonporous surfaces." Clorox on grout sets the bleach products beside the bleach-free wipes, which lift no stains.
| Mold Armor (FG502) | Tilex Mold & Mildew Remover | RMR-86 | Clorox bleach, per Clorox's grout guide | |
|---|---|---|---|---|
| Bleach strength | 4.0% (label) | 2.4% (label) | 1-5% (SDS, June 2026) | 1/3 cup per gallon of water |
| pH | 12-13.5 (SDS 2021) | 12.4-12.8 (Canada SDS 2021) | 11.37 (SDS 2026) | Not given |
| EPA registration | 4091-23 | 5813-24 | None | Guide is not a label |
| Grout named | "Sealed grout" only | Grout and cement (porous); "Sealed Grout" | "Grout lines" (maker's page) | Grout, with dilution "for hard, nonporous surfaces" |
| Kill claim on bare grout | No | Yes: 10 min, rinse | No | No: a stain method |
| Stain step | 10 min, rinse | Until stains go, rinse | At least 15 s, rinse | 10 min, scrub, rinse |
None of the four is a routine grout cleaner by TEC's rule, and for grout that has no stain, a pH-neutral cleaner does the weekly job.
Where this answer stops applying
This page covers Mold Armor Mold & Mildew Killer + Quick Stain Remover (FG502) on its four EPA labels from 2017 to 2023, its 2018 printed bottle and its April 2021 safety data sheet. EPA lists more than 30 Mold Armor names under the same registration, such as Rapid Clean Remediation. Other Mold Armor products, such as the E-Z House Wash line (EPA 4091-19), sit under other registrations, so read the label on your bottle. No source found measures how much color or sealer one Mold Armor treatment removes, so this page gives no figure. The label does not say how well a sealer must perform for grout to count as sealed; the water drop test is the practical check, not a label rule. It does not rule on premixed acrylic or urethane grout, or on grout younger than its cure time; their makers' care sheets govern. Grout that is soft, sandy or cracked has a cause other than mildew, and bleach will not fix it. A musty smell with little to see can mean mold behind the tile, which no spray reaches. The breathing and eye warnings apply on any surface: use it only with fresh air moving through the room, and never after an acid or ammonia cleaner without a rinse between.
Frequently asked questions
Is Mold Armor safe on grout?
On sealed grout, yes: the bottle lists "sealed grout" among its surfaces. On unsealed cement grout it will remove stains, but its kill claim does not cover bare grout. Rinse after 10 minutes either way, and test colored grout first.
Does Mold Armor kill mold in grout?
Only on sealed grout, where the label sets 60 seconds. Unsealed grout is porous, and the kill claim is for hard, non-porous surfaces. Tilex Mold & Mildew Remover has a kill line for bare grout: 10 minutes, then rinse.
Will Mold Armor bleach colored grout?
Barr does not say, and no maker has published a test. Simple Green says chlorine bleach leaches color from tinted grout, and Mold Armor is 4.0 percent bleach. Test a hidden joint, judge it dry, and use oxygen bleach for routine stain work.
How long do you leave Mold Armor on grout?
The label says wait 10 minutes for stains to disappear, then rinse with water or wipe with a damp sponge. The kill time on hard, non-porous surfaces, including sealed grout, is 60 seconds.
Do you have to rinse Mold Armor off grout?
Yes. The stain step ends with "rinse with water or wipe with a damp sponge." Grout is porous, so rinse it well. Rinse vinyl and rubber within 15 minutes.
Does Mold Armor remove grout sealer?
Barr does not say. Aqua Mix bans bleach on its Sealer's Choice Gold, though, so do a water drop test the day after. If the drops soak in, reseal.
What is in Mold Armor Mold and Mildew Killer?
Sodium hypochlorite 4.0 percent and sodium carbonate 1.0 percent on the label. Barr's 2021 sheet also lists sodium hydroxide at 0.1 to 1.0 percent and gives pH 12 to 13.5.
Sources and standards
- US EPA, Mold Armor Formula 400 label, EPA Reg. No. 4091-23: registration of October 2, 2017; amendment of March 9, 2018; notification of December 16, 2019; notification of April 12, 2023
- US EPA, Pesticide Product Label System, product record for 4091-23, with alternate brand names (read November 19, 2026)
- W.M. Barr, Mold Armor Mold & Mildew Killer + Quick Stain Remover printed label, FG502, 32 fl oz (copyright 2018)
- W.M. Barr, Mold Armor Mold & Mildew Killer + Quick Stain Remover safety data sheet, revision April 7, 2021
- US EPA, Clorox bleach sanitizer spray, EPA Reg. No. 5813-85, notice of June 9, 2005 ("Grout is a porous surface")
- US EPA, Tilex label, EPA Reg. No. 5813-24: amendment letter of April 28, 2003 and notification of June 4, 2024
- The Clorox Company of Canada, Tilex Mold & Mildew Remover safety data sheet, revision 2 (August 27, 2021)
- RMR Solutions, RMR-86 safety data sheet, RMR-001 version 4 (June 9, 2026), and RMR-86 product page
- Clorox, How to clean grout (read November 2026)
- TEC Specialty Products, Power Grout Ultimate Performance Grout: Cleaning and Maintenance (November 2025)
- Custom Building Products, Aqua Mix Sealer's Choice Gold, TDS-158 and Aqua Mix Grout Colorant, TDS-173
- LATICRETE, SPECTRALOCK PRO Premium Grout, DS-681.0-0217
- MAPEI, Keracolor S safety data sheet, version 10 (March 26, 2026)
- Simple Green, How to clean grout
Grout Atlas guidance is checked against ANSI A108/A118 and ISO 13007 requirements, the TCNA Handbook and manufacturer technical data sheets. Product formulations change, so confirm details on the current data sheet for the product you buy. Spotted an error? Report a correction.