Can You Use Scrubbing Bubbles on Grout?

CleaningUpdated 16 min readHow we research

On this page
  1. What Scrubbing Bubbles is
  2. What is in the foam
  3. What the EPA labels say about grout
  4. Why it cleans grout but does not disinfect it
  5. What SC Johnson's tile and grout tip says
  6. Why you should rinse the joint
  7. A worked case: one shower, two grouts
  8. Grout by grout: where the makers draw the lines
  9. Scrubbing Bubbles or not: grout by grout
  10. The toilet gels that share the name
  11. How to clean grout with Scrubbing Bubbles
  12. Scrubbing Bubbles, Kaboom or a wipe?
  13. Where this answer stops applying
  14. Frequently asked questions
  15. Sources and standards

Yes. Scrubbing Bubbles bathroom foam is safe on cement and epoxy grout for soap scum, if you rinse it off. It is a mild alkaline cleaner, pH 10.8 to 12 on SC Johnson's own sheets, with no acid and no chlorine bleach. That puts it close to wet cement grout, which MAPEI measures at pH 11.00. Two limits matter. Its germ and mold claims cover hard, non-porous surfaces, and bare grout is porous, so it cleans the joint but does not disinfect it or kill mold in it. And foam left to dry in the joint is film, so rinse the grout with water even where the can says wiping is enough.

Key takeaways

  • Scrubbing Bubbles bathroom foams are detergent plus quat disinfectants, pH 10.8 to 12. No acid, no bleach. That suits cement grout of any color and epoxy grout.
  • The 2006 EPA label in most search results never named grout. It was cancelled in 2018. Today's labels list "Sealed grout" (Reg. No. 4822-594) and "Grout" (Reg. No. 4822-625).
  • Disinfecting and mold claims stop at hard, non-porous surfaces. EPA has ruled that "Grout is a porous surface," so the foam cleans grout but does not sanitize it.
  • Rinse the joints with water after cleaning. Daltile asks for a clear water rinse after cleaning glazed tile "to prevent film formation."
  • Keep it off natural marble, brass, acrylic and recolored grout as a habit. The bleach toilet gel that shares the name is a different product: pH 12 to 14, bleach and lye.

What Scrubbing Bubbles is

Scrubbing Bubbles is a brand of bathroom cleaners made by SC Johnson, the company behind Windex and Glade. When people ask about it on grout, they mean the bathroom foam: the aerosol can or trigger spray sold as Bathroom Grime Fighter, Mega Shower Foamer or Disinfectant Bathroom Cleaner. The brand also covers toilet gels and toilet brushes, which are covered further down.

Four terms decide the answer, so here they are in plain words. Grout is the filler between tiles. Most of it is cement grout, a sand and cement mix that dries hard but stays porous, like a very fine sponge. Acid dissolves the cement in it. pH is a 0 to 14 scale of how acidic or alkaline a liquid is. 7 is neutral, and each whole step is ten times stronger. Wet cement grout is alkaline: MAPEI's sheet for Keracolor S sanded grout (version 10, March 26, 2026) gives pH 11.00.

Quats, short for quaternary ammonium compounds, are the germ killers in the foam. They are the same family as the germ killers in Clorox Disinfecting Wipes. Hard, non-porous is EPA wording for a surface that liquid cannot soak into, such as glazed tile, glass or chrome. A germ claim on an EPA label only holds on the surfaces the label names, and only when you follow its contact time.

What is in the foam

The disinfectant foams' sheets list a glycol ether solvent, a mineral-grabbing agent called EDTA and a fraction of a percent of quats. The Grime Fighter sheets name less, and both withhold the rest of the recipe as a trade secret. Soap scum is the gray film left when soap reacts with the minerals in hard water, and EDTA grabs those minerals.

Scrubbing Bubbles bathroom foams on SC Johnson and Diversey safety data sheets
Product (sheet, date)FormMain ingredients listedpHHazard class
Bathroom Grime Fighter, Citrus (SDS 350000033329, July 27, 2017)LiquidDiisopropanolamine 1-5%10.8Not classified
Bathroom Grime Fighter, Citrus (SDS 350000033863, December 14, 2017)AerosolIsobutane propellant 5-10%12.0Eye irritation, Category 2
Disinfectant Scrubbing Bubbles XXIII Bathroom Cleaner, Fresh Clean (SDS 350000021255, February 24, 2015)AerosolGlycol ether 5-10%, EDTA, four quats 0.0001-0.1% each11.8Eye irritation, Category 2A
Disinfectant Scrubbing Bubbles XXIII, Fresh Citrus, EPA Reg. No. 4822-594 (SDS 350000021341, January 29, 2018)AerosolGlycol ether 5-10%, EDTA 1-5%, four quats11.8Eye irritation, Category 2B
Scrubbing Bubbles Disinfectant Bathroom Cleaner, Diversey professional, EPA Reg. No. 70627-73 (SDS MS0800250, January 22, 2015)AerosolGlycol ether 5-10%, EDTA 3 to under 5%11.8Serious eye damage, Category 1; corrosive to metals

The liquid and aerosol versions of Grime Fighter Citrus sit 1.2 pH steps apart, about 16 times. Both sheets say "Do not mix with bleach or any other household cleaners." The Diversey professional can is the strongest on paper. Its sheet rates it Category 1 for eye damage and corrosive to metals, and EPA lists its registration as inactive since August 21, 2019. None of the five sheets lists an acid or chlorine bleach. Every one sits within one pH step of wet grout. The grout cleaner pH chart puts them next to the other common cleaners.

What the EPA labels say about grout

The label most often quoted is EPA Reg. No. 4822-547, accepted March 15, 2006, for "Antibacterial Scrubbing Bubbles XXI Bathroom Cleaner." It lists "glazed ceramic tile, tile" among the surfaces it cleans, and adds: "not recommended for use on acrylic, brass or natural marble." The word grout does not appear. That label is out of date, though. EPA's pesticide database shows 4822-547 cancelled at SC Johnson's request on April 13, 2018.

The foams sold since then carry newer labels, and both name grout.

  • EPA Reg. No. 4822-594 (latest label accepted May 26, 2021) covers "Scrubbing Bubbles Bathroom Disinfectant Bathroom Grime Fighter" and "Scrubbing Bubbles Bathroom Disinfectant Mega Shower Foamer." Both names were added on April 30, 2018. Its surface list includes "Sealed grout," "Sealed marble" and "Sealed natural stone." It also carries optional text: "Do not use on ... acrylic, brass, natural marble, finished wood, painted or worn surfaces." The actives are four quats totaling 0.24 percent.
  • EPA Reg. No. 4822-625 (label dated April 30, 2025) covers "Scrubbing Bubbles Disinfectant Bathroom Grime Fighter I," a trigger spray with 0.26 percent quat. Its list of items includes "Grout" and "Caulk." Its cleaning direction ends in one word: "Rinse."

So the old claim that the label "does not name grout" was true of a label that left the market in 2018. Current labels do name it. What they do not do is extend the germ claims to bare grout, and that is the next section.

Why it cleans grout but does not disinfect it

Every Scrubbing Bubbles label read for this page ties its kill claims to hard, non-porous surfaces. The 4822-594 label says: "Spray 6-8 inches from hard non-porous surface(s) until thoroughly wet. Let stand for 5 minutes." The 4822-625 label says "Let surface stand visibly wet for 5 minutes and wipe."

Bare grout is not one of those surfaces. When Clorox asked EPA in 2005 to put grout on a sanitizer label (Reg. No. 5813-85, June 9, 2005), EPA's reply said: "Grout is a porous surface. All references to grout have been" taken out of the proposed label. Liquid soaks into the joint, so the label's wet contact time cannot be shown to work there. Sealed grout is the one grout on 4822-594's surface list.

The mold claim is narrower still. Neither current label claims to kill mold or remove mold stains. Both say the foam will "inhibit and prevent the growth of mold and mildew," and 4822-594 adds "On hard non-porous surfaces." The foam has no bleach, so it does not lighten the black or pink spots in a joint. For those, see grout mold and mildew.

What SC Johnson's tile and grout tip says

SC Johnson's page "How to Clean Tile & Grout" (copy of June 7, 2026) tells you to use the Bathroom Grime Fighter aerosol "to go to work, deep down, in between bathroom tiles and remove 100% of soap scum." It goes on: spray on the foam, and "use an old toothbrush if any grime or mildew really gives you a hard time," then wipe it away. The steps are short: spray from 6 to 8 inches, "Allow foam to penetrate," and "Remove by wiping away foam with a cloth or sponge. On chrome, rinse with water."

That is a fair tip for soap scum, and the chemistry above backs it. Two words in it go further than the labels. "Mildew" on the tip page does not make the foam a mold remover, since no label claims that. And "wipe away" leaves the joint holding whatever the cloth missed, which is the problem in the next section.

Why you should rinse the joint

The labels give you a choice. The 4822-594 label says "Rinse clean or wipe away foam with cloth or sponge," and adds "No need to wipe dry." The newer 4822-625 label just says "Rinse." On grout, take the rinse.

Daltile's tile care guide says glazed tile can be cleaned with "a pH neutral liquid cleaner (soapless). Follow with a clear water rinse and wipe dry to prevent film formation." Scrubbing Bubbles is neither neutral nor soapless, so the case for rinsing is stronger, not weaker. A wiped tile face is fine. A grout joint is a groove that soaks up liquid, and a cloth skims over it. What dries there is detergent, EDTA and quat: the film Daltile's rinse is meant to prevent.

Rinsing also protects sealer. Aqua Mix's sheet for Sealer's Choice Gold (TDS-158, March 23, 2023) says "high-alkaline, acidic, or solvent-based cleaners will affect wear." The foam is alkaline and holds a glycol ether solvent, so it should not sit on sealed grout.

A worked case: one shower, two grouts

Take a shower with white glazed ceramic wall tile and white cement grout, never sealed. The floor is gray porcelain mosaic with charcoal cement grout, sealed when it was installed. There is a soap scum film on the lower walls and the floor, and a few black mildew dots in the corner joints. On the shelf is a can of Scrubbing Bubbles Bathroom Grime Fighter.

Start with the walls. The grout is white, bare cement, and the foam has no acid or bleach in it, so nothing here rules it out. Spray the lower walls from 6 to 8 inches and let the foam sit a few minutes. Scrub the joints with a nylon brush, then rinse the wall with the shower head. Wipe the chrome valve trim, as the label asks.

Next, the floor. The grout makers' color warnings are about acid and bleach, and the foam has neither. But this grout is sealed, and TDS-158 says alkaline and solvent cleaners wear sealer. So use the foam here when the film builds up, not every week, and rinse it all away. Then put a few drops of water on the joints near the drain. If they darken instead of beading, the water drop test says it is time to reseal.

Last, the mildew dots. The foam will not lift them, because there is no bleach in it. On the white wall grout, a bleach product is the usual next step. On the charcoal floor grout, start with oxygen bleach, since Simple Green warns that "chlorine bleach will leach color out of tinted grout." Rinse off all the Scrubbing Bubbles first. Its sheet says not to mix it with bleach.

Change one fact and the answer moves. If the floor were marble, the label's "natural marble" warning would rule the foam out there. If the walls were recolored with a grout colorant, the foam would drop to an occasional cleaner, for the reason in the next section.

Grout by grout: where the makers draw the lines

White or light cement grout between glazed tile. Yes, for soap scum, scrubbed and rinsed. This is the case SC Johnson's own tip describes.

Colored cement grout. Yes, rinsed. Grout makers warn about two things on colored joints. LATICRETE's sheet for PERMACOLOR grout (DS-250-1026) says "DO NOT use acid to clean colored grout joints," and Simple Green warns that chlorine bleach leaches tint. The bathroom foam contains neither. If the color is already patchy, fading grout explains the usual causes.

Sealed cement grout. The 4822-594 label lists "Sealed grout," so the foam is allowed. Aqua Mix TDS-158 says alkaline and solvent cleaners "will affect wear," so use it when soap scum builds rather than as the daily spray, and rinse.

Recolored grout. Aqua Mix's colorant sheet (TDS-173, February 28, 2023) says "high-alkaline, acidic or solvent-based cleaners will affect wear." Make a neutral cleaner the routine one and keep the foam for the odd deep clean. TDS-173 also says to avoid direct scrubbing on newly colored joints "for 20 days to allow a full cure." More in grout colorant.

Epoxy grout. Yes. LATICRETE's chemical chart for SPECTRALOCK PRO Premium grout (DS-681.0-0217) rates 45 percent potassium hydroxide "R," recommended, even after 7 days. That is a far stronger alkali than any foam in the table. The same sheet says its glow-in-the-dark DAZZLE additive "might discolor from strong alkali cleaners and acids," so treat glow grout with a neutral cleaner. See cleaning epoxy grout.

Natural stone tile. No on unsealed natural marble: both the 2006 and the 2021 labels warn against it. The 2021 label lists sealed marble and sealed stone, but Daltile says "many of the cleaners acceptable for use on ceramic tile can stain, damage or dull stone." For stone, use a cleaner made for stone. See grout for natural stone.

Scrubbing Bubbles or not: grout by grout

Scrubbing Bubbles bathroom foam on grout, from the rulings and sources above
Grout or surfaceBathroom foam (pH 10.8-12)Why
White or light cement grout, glazed tileYes, scrub and rinseNo acid or bleach on any sheet; SC Johnson tip; Daltile rinse rule
Colored cement groutYes, rinseLATICRETE DS-250-1026 bans acid; Simple Green: bleach leaches tint; the foam has neither
Sealed cement groutYes, rinse; not the daily sprayEPA 4822-594 lists "Sealed grout"; Aqua Mix TDS-158: alkaline and solvent cleaners affect wear
Recolored groutNot routine; no scrubbing for 20 days after coloringAqua Mix TDS-173
Epoxy groutYes; neutral cleaner on DAZZLE glow groutLATICRETE DS-681.0-0217: 45% KOH R at 7 days; DAZZLE strong alkali note
Unsealed natural marbleNoEPA 4822-547 and 4822-594 labels
Sealed natural stoneUse a stone cleaner insteadDaltile: ceramic tile cleaners can "stain, damage or dull stone"
Disinfecting the grout itselfNot claimedLabels: hard, non-porous only; EPA 5813-85: "Grout is a porous surface"
Mildew stains in the jointWill not remove themNo bleach; labels claim to inhibit growth on non-porous surfaces only

The toilet gels that share the name

Search results for Scrubbing Bubbles mix the bathroom foam with the toilet products, and two of them are gels.

Scrubbing Bubbles Toilet Cleaning Gel is the stamp you press onto the inside of the bowl. SC Johnson's sheet for the Arctic Splash scent (SDS 350000022678, March 19, 2015) gives its use as a "Cage less rim block." It lists glycerin 5-10 percent, a detergent 1-5 percent and fragrance 1-5 percent, pH 4.5, and it is not classified as hazardous. It is made for the bowl, not for tile, and nothing on its sheet points it at grout. If some lands on a floor joint, wipe it up with water.

Scrubbing Bubbles Bubbly Bleach Gel is a toilet bowl cleaner, and it is a different matter. Its sheet (SDS 350000030870, August 11, 2016) lists sodium hypochlorite, which is chlorine bleach, at 1-5 percent and sodium hydroxide, which is lye, at 1-5 percent. It gives pH 12 to 14 and rates it Skin Corrosion 1B: "Causes severe skin burns." Keep it in the bowl. If it drips on grout, rinse it off, and treat colored grout by the bleach on grout rules. The toilet bowl cleaner on grout page covers the acid gels from other brands.

SC Johnson also sells a Scrubbing Bubbles Foaming Bleach Bathroom Cleaner. No safety sheet for it was read for this page. It is a bleach product by its name, so the bleach rules apply to it, not the rulings above.

Bottom line: Scrubbing Bubbles bathroom foam is a good soap scum cleaner for cement grout of any color and for epoxy grout. Spray, wait a few minutes, scrub with a nylon brush and rinse the joints with water. It does not disinfect grout or kill mold in it. Go easy on sealed and recolored grout, and keep it off natural marble.

How to clean grout with Scrubbing Bubbles

  1. Check the name. If it says "Bleach," the bleach rules apply. If it is a toilet gel, it is not a grout cleaner.
  2. Run the fan. The aerosol sheets rate it an eye irritant, so keep the spray below face height.
  3. Rinse off any other cleaner first, above all bleach. The sheets say not to mix it with other cleaners.
  4. Spray from 6 to 8 inches until the joints are covered. For a wide-spray can, the 4822-594 label says 12 to 15 inches and a 3 minute wait.
  5. Let it sit a few minutes. Do not let it dry on the wall.
  6. Scrub the joints with a nylon brush or an old toothbrush, as SC Johnson's tip suggests.
  7. Rinse with plenty of clean water, then wipe chrome dry. If the gray film keeps coming back, soap scum and hard water on grout explains why.

Scrubbing Bubbles, Kaboom or a wipe?

Kaboom Foam-Tastic is the closest match: an alkaline foam at pH 12 with EDTA and no bleach, and it gets the same grout rulings. The Kaboom Heavy Duty spray is a different animal, a sulfamic acid at pH 0.8 to 1.2, so read Kaboom on grout before you swap one can for the other. A Clorox wipe is gentler, near neutral at pH 6.25 to 8.5, and fine for a quick pass on any grout. Like the foam, it cleans grout but does not disinfect it.

Where this answer stops applying

This page covers the Scrubbing Bubbles bathroom foams on the five sheets in the table and the EPA labels 4822-547 (2006), 4822-594 (2021) and 4822-625 (2025). No safety sheet sold under the Mega Shower Foamer name was found, so its pH is not stated here. It shares registration 4822-594 with the XXIII bathroom cleaner, whose sheets give 11.8. No sheet for the 4822-625 trigger gives a pH either. Formulas change under the same name, so the label on your can decides. No Scrubbing Bubbles document addresses grout color or sealer life, and no source measures how much grout one cleaning removes, so this page gives no figure. It does not cover premixed acrylic or urethane grout, which their makers' sheets govern, or grout that is cracked or crumbling, which needs repair rather than cleaning. It does not rule on the Foaming Bleach Bathroom Cleaner. The one rule that holds everywhere: do not mix the foam with bleach or any other cleaner.

Frequently asked questions

Is Scrubbing Bubbles safe on grout?

Yes, the bathroom foam is safe on cement and epoxy grout used as directed and rinsed. It is alkaline, pH 10.8 to 12, with no acid or bleach. Keep it off natural marble and use it sparingly on sealed or recolored grout.

Does Scrubbing Bubbles kill mold on grout?

No. Its labels claim only to inhibit mold and mildew growth on hard, non-porous surfaces, and EPA treats grout as porous. It has no bleach, so it will not lighten mildew stains in a joint.

Will Scrubbing Bubbles discolor colored grout?

No source says it does, and it lacks the two things grout makers warn about on colored joints: acid and chlorine bleach. Rinse it off so no residue dries in the joint.

Do I have to rinse Scrubbing Bubbles off?

The 2021 label lets you rinse or wipe, but on grout, rinse. Daltile asks for a clear water rinse after cleaning tile to prevent film, and the 2025 Grime Fighter I label simply says "Rinse."

Does Scrubbing Bubbles have bleach in it?

The bathroom foams do not. The Bubbly Bleach toilet gel and the Foaming Bleach Bathroom Cleaner do, so read the name on the bottle.

Can I use the Scrubbing Bubbles toilet gel on grout?

No. The stamp gel is a rim block for the bowl, not a tile cleaner. The Bubbly Bleach Gel is bleach and lye at pH 12 to 14, so rinse any drips off grout at once.

Sources and standards

Grout Atlas guidance is checked against ANSI A108/A118 and ISO 13007 requirements, the TCNA Handbook and manufacturer technical data sheets. Product formulations change, so confirm details on the current data sheet for the product you buy. Spotted an error? Report a correction.