Can You Use Pine-Sol on Grout?
On this page
- Two Pine-Sols, two chemistries
- What glycolic acid does to cement grout
- What Pine-Sol tells you to do on grout
- Full strength and the disinfecting claim
- What grout, sealer and tile makers say
- Which Pine-Sol, grout by grout
- Epoxy, urethane and premixed grout
- Mopping tile floors with Pine-Sol
- Where this answer stops applying
- Frequently asked questions
- Sources and standards
Yes, diluted and rinsed, but know which Pine-Sol you are holding. Original Pine-Sol, the amber one, is an acid cleaner: Clorox's safety data sheet gives glycolic acid as the active ingredient and a pH of 2.1 to 2.6. The scented Multi-Surface versions (Lemon Fresh, Lavender Clean) contain no acid and run pH 10 to 11. On sealed, colored or recolored grout the difference decides the answer.
Key takeaways
- Original Pine-Sol no longer contains pine oil. Its EPA label lists 1.75 percent glycolic acid, and its pH (2.1 to 2.6) is in the same band as vinegar.
- Lemon Fresh and Lavender Clean Pine-Sol are a different formula: a surfactant with no acid, pH 10 to 11, and no EPA disinfectant registration.
- Pine-Sol's own grout method is 1/8 cup of Original per gallon of water, 5 to 10 minutes, scrub, rinse. At that dilution the glycolic acid is about 0.014 percent.
- Full strength is the problem: the 10-minute disinfecting use puts 1.75 percent acid on the joint, and the label's disinfection claims cover hard, nonporous surfaces only. Cement grout is porous.
- Skip Original on marble and limestone (the label says so), on sealed grout, and on colored or recolored grout. Never mix any Pine-Sol with bleach.
Two Pine-Sols, two chemistries
Most pages that answer this question describe Pine-Sol as one product, and they disagree about it. Some call it a mild all-purpose cleaner; others warn that its "high-pH formula" breaks down grout. Both are partly right, because the brand sells two unrelated chemistries.
The Clorox Company's safety data sheet for Original Pine-Sol Multi-Surface Cleaner (revision 3, February 4, 2019) lists alkyl alcohol alkoxylate at 3 to 7 percent and glycolic acid at 1 to 5 percent, with a pH of 2.1 to 2.6. The first issue of that sheet (January 5, 2015) gave pH 2 to 3, and the Canadian sheet for Original Pine-Sol Multi-Surface Cleaner Disinfectant (August 11, 2021) again gives 2.1 to 2.6. The EPA-accepted master label for registration 5813-101 (April 11, 2023) states the exact figure: "Glycolic Acid ... 1.75%."
The scented line is built differently. Clorox's sheet for Lemon Fresh Pine-Sol Multi-Surface Cleaner (April 19, 2015) lists one ingredient above the reporting threshold, an alkyl alcohol alkoxylate at 1 to 5 percent, and a pH of 10 to 11. The Lavender Clean sheet (March 23, 2018) and the Canadian Lemon Fresh sheet (July 26, 2021) give the same pH range and no acid. None of the three lists an EPA registration number, so they are cleaners, not registered disinfectants.
| Product | Active chemistry | pH | Source |
|---|---|---|---|
| Original Pine-Sol (amber) | Glycolic acid 1.75%, alcohol alkoxylate 3-7% | 2.1 to 2.6 | Clorox SDS (2019), EPA label 5813-101 (2023) |
| Lemon Fresh Pine-Sol | Alcohol alkoxylate 1-5%, no acid | 10 to 11 | Clorox SDS (2015, Canada 2021) |
| Lavender Clean Pine-Sol | Alcohol ethoxylate 1-5%, no acid | 10 to 11 | Clorox SDS (2018) |
| Pine-Sol Cleaner Disinfectant, 1995 label | Pine oil | Not stated | EPA label 5813-36 (1995) |
| White vinegar | About 5% acetic acid | About 2.5 | See vinegar on grout |
| Original Dawn dish liquid | Alkyl sulfate surfactants | 9 (10% solution) | P&G SDS (2017) |
The pine oil version is why the old reputation survives. Pine-Sol's 1995 EPA label lists "PINE OIL" as the active ingredient and names grout among the surfaces to clean. Clorox introduced the glycolic acid Original in January 2013 and announced in January 2014 that Pine-Sol products would no longer contain pine oil, citing its limited supply and cost. The bottle still smells of pine and still says Original, but the cleaner inside changed from a solvent-and-detergent product to an acid one. Advice written about the old bottle, or about the scented ones, does not transfer.
What glycolic acid does to cement grout
Cement grout is held together by the same calcium compounds as concrete. The chemical distributor ChemPoint, in a technical note for cleaner formulators, states the mechanism plainly: concrete's structure is "held together by calcium compounds, primarily calcium silicate hydrate (C-S-H) and calcium hydroxide (portlandite)," and "When glycolic acid contacts hardened concrete, it reacts with these calcium compounds to form calcium glycolate, a water-soluble salt." The same note says glycolic acid "removes cement haze, grout residue, efflorescence, and mineral deposits." That is a selling point for a haze remover and a warning for a floor cleaner.
The dose is what separates the two. ChemPoint gives a typical ready-to-use concrete remover as about 14 percent glycolic acid. Full-strength Original Pine-Sol is 1.75 percent, one eighth of that. Pine-Sol's grout instructions dilute it again, roughly 1 part in 129, which leaves about 0.014 percent glycolic acid in the bucket. What adds up is repetition and contact time: weekly mopping with acid solution left to dry in the joints, or full-strength product left on for ten minutes.
The same chemistry explains why Original Pine-Sol is good at the things the label promotes. The EPA-accepted label carries optional claims that it "Cuts through soap scum" and is tough on "rust -and/or- hard water," both mineral soils that an acid dissolves and a detergent does not. Scented Pine-Sol, with no acid, will not do that job, as covered in soap scum and hard water on grout.
What Pine-Sol tells you to do on grout
Pine-Sol's grout cleaning page gives one method, for Original only:
- Wear goggles and wipe loose dirt off the tile and grout with a damp cloth or sponge.
- Mix "⅛ cup of Pine-Sol Original Cleaner to a bucket containing one gallon of water."
- Apply it to the grout lines with a nylon brush, in small sections, and scrub.
- "Allow the Pine-Sol solution to sit on the grout for 5-10 minutes," then scrub again.
- Rinse the tile and grout "thoroughly to remove any remaining Pine-Sol residue," and towel dry.
The same page adds: "Do not use on marble, aluminum, copper or wood that is unfinished, unsealed, unpainted, waxed, oiled or worn." The tile page notes that the dilution depends on whether you have the current concentrated formula or the older one, which is why the EPA master label still reads 1/4 cup per gallon for general cleaning. Follow the rate printed on your bottle.
That method is reasonable for unsealed white or light cement grout between glazed tile, used now and then. What makes it gentle is the low dilution, the short dwell and the rinse.
Full strength and the disinfecting claim
The 5813-101 label offers two stronger uses. For tough cleaning jobs: "use full strength and rinse immediately." To disinfect, apply full strength on "hard, nonporous surfaces" and "Allow surface to remain visibly wet for 10 min[utes]." The organism table lists bacteria and viruses, all at 10 minutes, and no mold or mildew.
Unsealed cement grout is not a hard, nonporous surface. It absorbs water, which is why it darkens when wet (see grout porosity and absorption), so the disinfecting directions do not cover it. Ten wet minutes of 1.75 percent glycolic acid on a cement joint is also the harshest thing the bottle can do to grout: acid at full strength, soaking in, for the longest time the label names. If the goal is mildew in shower grout, Pine-Sol is not registered for it; the methods in grout mold and mildew are.
What grout, sealer and tile makers say
No grout data sheet names Pine-Sol. They name the chemistry, and the rules are consistent:
- LATICRETE's PERMACOLOR Grout data sheet (DS-250-1026): "DO NOT use acid to clean colored grout joints." Routine maintenance is a STONETECH cleaner or "a neutral pH cleaner."
- Custom Building Products' Polyblend Plus sheet (TDS-360): "Clean with a pH-neutral cleaner." Acid haze cleaners are allowed only after ten days and with a test in an inconspicuous area.
- Aqua Mix Sealer's Choice Gold (TDS-158): "Do not use cleaners containing ammonia, acids or bleach." Its expected-wear note adds that "high-alkaline, acidic, or solvent-based cleaners will affect wear."
- Aqua Mix Grout Colorant (TDS-173): "harsh cleaning methods and high-alkaline, acidic or solvent-based cleaners will affect wear" of recolored grout.
- Daltile's Tile Care & Maintenance guide: glazed ceramic and porcelain are cleaned with "clear water and/or a pH neutral liquid cleaner (soapless)," and "Neither sealing nor acid cleaning is recommended for any of Daltile's glazed ceramic or porcelain tile." Natural stone cleaners "should never contain acid or bleach."
Neither Pine-Sol is the neutral cleaner these sheets ask for. The scented formula breaks none of the bans, since it has no ammonia, acid or bleach; Original breaks the acid ban on sealed grout and, as LATICRETE words it, on colored grout.
Which Pine-Sol, grout by grout
| Situation | Original (glycolic acid) | Lemon Fresh or Lavender Clean | Why |
|---|---|---|---|
| Unsealed white or light cement grout, glazed tile | Occasionally, at Pine-Sol's dilution, rinsed | Yes, diluted and rinsed | Pine-Sol's own grout method; acid is weak at 1/8 cup per gallon |
| Colored cement grout | No | Yes, diluted and rinsed | LATICRETE: no acid on colored grout joints |
| Sealed cement grout | No | Yes, occasionally; sealer maker's neutral cleaner first | TDS-158: no ammonia, acids or bleach |
| Recolored grout (colorant) | No | Sparingly | TDS-173: acidic and high-alkaline cleaners affect wear |
| Epoxy grout | Diluted, rinsed | Yes | LATICRETE rates its premium epoxy resistant to 5% lactic, acetic and citric acids; glycolic acid is not on the chart |
| Grout less than 10 days old | No | Wait for the grout sheet's cure time | Custom allows acid cleaners on new grout only after 10 days |
| Marble, limestone, travertine | No | Use a stone cleaner | Pine-Sol label: not on marble; Daltile: no acid on stone |
| Soap scum or hard water film | Works, spot use, rinsed | No effect | Mineral films need acid; detergent alone does not dissolve them |
| Mildew in shower grout | Not registered for it | Not registered for it | No mold or mildew on the 5813-101 organism table |
Bottom line: For mopping a tile floor with cement grout, the scented Pine-Sol is the better bottle: no acid, nothing the sealer makers ban, and a rinse keeps it from leaving film. Keep Original for an occasional soap scum or hard water job on white unsealed cement grout or epoxy, at 1/8 cup per gallon, under 10 minutes, rinsed. Do not use Original full strength on grout, on sealed or colored joints, or anywhere near marble.
Epoxy, urethane and premixed grout
Epoxy grout is far more acid resistant than cement. LATICRETE's SPECTRALOCK PRO Premium data sheet (DS-681.0-0217) rates the grout resistant to 5 percent lactic, acetic and citric acid at 30 minutes, 24 hours and 7 days. Glycolic acid is not on that chart, so the site does not claim a rating for it, but a 0.014 percent solution rinsed off is far weaker than anything LATICRETE tested. The same sheet asks for "a neutral pH solution of soap and water" on its glow-in-the-dark DAZZLE version, which "might discolor from strong alkali cleaners and acids." Use soap and water on that one.
For urethane and premixed grouts, follow the grout's own care section. If you do not know what grout you have, treat it as cement; the grout type guide covers the families.
Mopping tile floors with Pine-Sol
Floors are where most people use Pine-Sol. Grout joints sit below the tile face, so mop water drains into them and dries there, as explained in cleaning floor grout. If Original is the bottle on the shelf, every mopping leaves a trace of acid solution in the joints of a cement grout floor. That is the pattern to avoid: weak acid, applied weekly, never rinsed.
Two habits fix it. Use the scented Pine-Sol for routine mopping and save Original for spot jobs. And rinse: the 1995 label said "No rinsing required" for floors and walls, but every grout and tile care sheet above ends with a clean-water rinse, and so does Pine-Sol's own grout page. A second bucket of plain water and a wrung-out mop is enough.
Safety: Original Pine-Sol's label says "Do not use or mix with bleach-containing products or other [household] cleaners," and the Canadian sheet adds toilet bowl cleaners, rust removers, acids and products containing ammonia. Bleach plus an acid releases chlorine gas. If you have just used bleach on grout, rinse the surface completely before any Pine-Sol touches it. Wear eye protection: Pine-Sol's own grout steps start with goggles.
Where this answer stops applying
The figures here come from Clorox's US and Canadian safety data sheets and the EPA label for registration 5813-101. Clorox reformulates, and other Pine-Sol scents and CloroxPro versions were not part of this comparison. Check the safety data sheet for the exact bottle if it is not Original, Lemon Fresh or Lavender Clean. The answer also assumes sound grout. Joints that are already sandy or eroded are not dirty, and no cleaner fixes them; see soft or crumbling grout.
For the place of each cleaner on the acid-to-alkali scale, use the grout cleaner pH chart. For the full order of methods, gentlest first, see how to clean grout, and for a detergent with no acid at all, Dawn on grout.
Frequently asked questions
Is Pine-Sol acidic or alkaline?
Both, depending on the bottle. Original Pine-Sol contains glycolic acid and has a pH of 2.1 to 2.6 on Clorox's safety data sheet. Lemon Fresh and Lavender Clean contain no acid and are pH 10 to 11.
Will Pine-Sol damage grout?
Not when diluted as Pine-Sol directs and rinsed off occasionally. Repeated use of Original without rinsing, or full-strength use, exposes cement grout to an acid that dissolves its calcium compounds. On sealed or colored grout, use the scented version or a neutral cleaner.
Does Pine-Sol kill mold in grout?
It is not registered for it. Original Pine-Sol's EPA label lists bacteria and viruses on hard, nonporous surfaces, with no mold or mildew, and cement grout is porous. The scented versions' sheets list no EPA registration.
Can I use Pine-Sol on natural stone grout?
Not Original. Its label says not to use it on marble, and acid etches marble, limestone and travertine. Use a cleaner labeled for stone.
Sources and standards
- The Clorox Company, Original Pine-Sol Multi-Surface Cleaner safety data sheet, revision 3 (February 4, 2019), and first issue (January 5, 2015)
- The Clorox Company of Canada, Original Pine-Sol Multi-Surface Cleaner Disinfectant safety data sheet (August 11, 2021)
- US EPA, master label for EPA Reg. No. 5813-101 (accepted April 11, 2023)
- US EPA, Pine-Sol Cleaner Disinfectant label, EPA Reg. No. 5813-36 (1995)
- The Clorox Company, Lemon Fresh Pine-Sol Multi-Surface Cleaner safety data sheet (April 19, 2015) and Canadian sheet (July 26, 2021)
- The Clorox Company, Pine-Sol Multi-Surface Cleaner, Lavender Clean, safety data sheet (March 23, 2018)
- Pine-Sol, How to Clean Grout and How to Clean Tile
- Wikipedia, Pine-Sol (formulation history)
- ChemPoint, Glycolic Acid for Concrete Cleaners and Removers
- LATICRETE, PERMACOLOR Grout data sheet, DS-250-1026 and SPECTRALOCK PRO Premium Grout data sheet, DS-681.0-0217
- Custom Building Products, Polyblend Plus Sanded Grout, TDS-360, Aqua Mix Sealer's Choice Gold, TDS-158 and Aqua Mix Grout Colorant, TDS-173
- Dal-Tile Corporation, Tile Care & Maintenance Guide
- Procter & Gamble, Ultra Dawn Original safety data sheet, version 1.02 (December 22, 2017)
Grout Atlas guidance is checked against ANSI A108/A118 and ISO 13007 requirements, the TCNA Handbook and manufacturer technical data sheets. Product formulations change, so confirm details on the current data sheet for the product you buy. Spotted an error? Report a correction.