Does Concrobium Kill Mold in Grout?

CleaningUpdated 14 min readHow we research

On this page
  1. What Concrobium is, and what a fungistat means
  2. Two labels, two different claims
  3. Which claim covers grout?
  4. Why "kills mold" keeps turning up
  5. Why the black stain stays
  6. Dry, don't rinse: Concrobium in a shower
  7. A worked case: one shower floor with gray grout
  8. How strong is it next to the grout?
  9. Grout by grout: where the makers draw the lines
  10. Concrobium on grout: what each label covers
  11. How to use Concrobium on shower grout
  12. Concrobium, Tilex or RMR-86?
  13. Where this answer stops applying
  14. Frequently asked questions
  15. Sources and standards

No, not by its label. Neither Concrobium label makes a kill claim that covers grout. Concrobium Mold Control (EPA Reg. No. 82552-1) is registered to stop mold from growing, and its label reaches porous surfaces like masonry, concrete and tile. Concrobium Mold Control Plus (82552-3) does kill mold, but only on hard, non-porous surfaces, and EPA treats grout as porous. Neither one takes out the black stain, so remove that first with bleach or peroxide. Then spray Concrobium on and let it dry. Do not rinse it off.

Key takeaways

  • Concrobium Mold Control is 0.95 percent sodium carbonate, and its label calls it a fungistat: it stops mold growth. The label never says it kills mold.
  • Mold Control Plus (1.00 percent sodium carbonate) kills two test fungi in 10 minutes, but only on hard, non-porous surfaces. EPA has said in writing that grout is porous.
  • Both labels say not to expect Concrobium to whiten stains. Remove black spots with bleach on white grout, or oxygen bleach or peroxide on colored grout, then apply Concrobium last.
  • Spray until evenly wet, then let it dry. The protective film is what does the work, so there is no rinse step. Reapply weekly and whenever the surface is washed.
  • Its pH is 11.1 to 11.5, close to cement grout itself. It has no bleach, acid or ammonia, but sealer and colorant makers say high-alkaline cleaners affect wear, so check sealed grout more often.

What Concrobium is, and what a fungistat means

Concrobium is a clear, odorless spray sold by Rust-Oleum. Two versions share the name, and the difference between them is the whole answer here.

  • Concrobium Mold Control, EPA Reg. No. 82552-1. The label lists sodium carbonate at 0.95 percent and water and other ingredients at 99.05 percent. EPA first registered it on October 13, 2005, and it carries no signal word such as Caution.
  • Concrobium Mold Control Plus, EPA Reg. No. 82552-3. The label lists sodium carbonate at 1.00 percent, and the signal word is Caution, for "moderate eye irritation."

Sodium carbonate is washing soda, a mild alkali. Older safety sheets for Mold Control (2011 and 2013) describe a "proprietary mixture of food-grade, inorganic salts and purified water," and the 2013 sheet lists trisodium phosphate at 0.5 to 5 percent. Rust-Oleum's technical data sheet (rev. July 24, 2019) gives the pH as 11.1 to 11.5.

Three terms decide the answer, so here they are in plain words.

  • A fungistat stops mold and other fungi from growing. It does not have to kill what is already there. A mildewstat does the same for mildew. A fungicide kills fungi.
  • An EPA registration is how a US product gets to make a pest claim. The label EPA accepts lists the claims, the surfaces and the directions. Claims the label does not make are not part of the registration.
  • A porous surface has tiny holes that soak up water. Glazed tile is not porous. Cement grout is, which is why it stays damp after the tile face dries. Grout porosity and absorption explains why.

Two labels, two different claims

Mold Control (82552-1): stops growth, porous surfaces allowed

The February 24, 2023 label lists its product claims as "[Hard Surface] [Fabric] Fungistat [and] [Hard Surface] Mildewstat." Pomerix's index of EPA labels files it the same way: product type "Fungistat."

The surface line is broad. The label says it is "For use on [the following] [both] [non-porous] [semi-porous] [porous] [hard] [and fabric] surfaces," and the list after it includes "masonry," "concrete" and "tile." The directions are headed "MOLD AND MILDEW CONTROL ON WOOD, WALLBOARD, FABRIC, CONCRETE AND MASONRY (CINDER) BLOCK."

How does it work? The label says Concrobium "dries on surfaces to create an invisible antimicrobial shield." It also says the product "encapsulates mold and fungal spores with a microscopic coating that inhibits [and prevents] its growth." In plain words, the dried film holds the spores so they cannot grow.

Mold Control Plus (82552-3): kills, hard non-porous only

The Plus label of October 18, 2022 is the one with kill language: "Kill[s] mold [and] mildew on hard, non-porous surfaces." Its organism list names the fungi it was shown to kill: Trichophyton interdigitale and Aspergillus niger, both "on hard, non-porous surfaces." The kill direction says to spray from 6 to 8 inches until thoroughly wet and "Allow to remain wet for 10 minutes."

Its prevention claim is narrow as well. The "prevents" claims carry a footnote: "For 7 days on hard non-porous surfaces and untreated wood, 28 days on cotton fabrics." The kill surface list includes "Bathroom Tile, Sealed (Glazed)," "Ceramic [Tile], Glazed" and "Porcelain [Tile], Glazed." Grout is not on either label.

Which claim covers grout?

Start with what grout is in EPA's eyes. When Clorox asked to list grout on a sanitizer label in 2005 (EPA Reg. No. 5813-85), EPA's reply said: "Grout is a porous surface. All references to grout have been" taken off the proposed label. The trouble is that liquid soaks into a porous joint, so the wet contact time on the label cannot be shown to work there.

Now walk each claim against that.

  • The Plus kill claim. It is tied to hard, non-porous surfaces in every line, so it does not reach grout. It covers the glazed tile face next to the joint.
  • The Plus prevention claim. Its footnote limits it to hard non-porous surfaces, untreated wood and cotton, so it does not reach grout either.
  • The Mold Control stop-growth claim. This is the only one that allows porous surfaces. It names masonry and concrete, which are cement and sand like grout, though the label never says the word grout.

So here is the ruling. On grout, the claim that applies is plain Mold Control's: it stops new growth. Rust-Oleum's own product page lists "grout" among the surfaces it "works on," which fits that claim. No Concrobium label says it kills mold in grout.

A kill claim on grout does exist, and that is why its absence matters. Tilex Mold & Mildew Remover's EPA label (5813-24, amendment of April 28, 2003) says: "TO Kill MOLD & MILDEW ON HARD, POROUS SURFACES such as grout and cement: Spray surface until thoroughly wet, let stand 10 minutes." EPA accepts that kind of claim when the testing backs it, and Concrobium's labels do not carry one. Tilex on grout covers that label.

Why "kills mold" keeps turning up

Two answers circulate because Concrobium's own words point two ways. The label lets Rust-Oleum print claims such as "[Eliminates] [and] [prevents] mold" and "[Physically encapsulates] [and] [crushes] mold." Rust-Oleum's product page says it "effectively eliminates existing mold." The Money Pit's page says Concrobium hardens into "an invisible film that physically crushes the mold micro-organism underneath."

The technical data sheet adds a test. It reports a fungicidal carrier test (ASTM QCT-2) against two molds with the result "Achieved >99% kill level." The 2013 safety sheet calls the product use "Fungicide and Fungistat/Mildewstat."

But the 2023 EPA label uses "kill" only for odors, never for mold. Its product claim is fungistat and mildewstat. "Eliminates" on that label sits next to "prevents," and the directions tie the effect to the dried film. So read "eliminates" as stopping growth, not a kill step with a contact time. On grout, the label is the claim that counts.

Why the black stain stays

Both labels say it plainly: "[Do not expect] Concrobium [to] [will not] whiten stains [on contact]." They add, "Mold stains may remain visible following treatment," and "In some cases, staining may be irreversible."

That fits the chemistry. Concrobium has no oxidizer, and the label lists "no ammonia, bleach, alcohol, acid." Bleach and peroxide are oxidizers, and they break down the colored parts of mold. That is why they lighten black spots and a fungistat does not.

The label gives the order of work, too: "If, [following treatment], additional steps are taken to [remove] [or] [cover] [address] [treat] the stain, reapply Concrobium as a final step." So the stain remover goes first and Concrobium goes last.

Rinse the stain remover off and let the grout dry before Concrobium goes on. The label would rather Concrobium did the first cleaning too, "to avoid possible interference from other chemicals," so leave nothing else on the joint.

Dry, don't rinse: Concrobium in a shower

Most bathroom sprays end with a rinse. Concrobium ends with drying. The prevention steps on the Mold Control label are:

  • Apply Concrobium on the area until evenly wet.
  • Wipe off excess wetness with a clean cloth, if you want it to dry faster or to avoid marks.
  • Allow treated surfaces to dry completely.

The film left behind is the product, so rinsing it away undoes the job. The cleaning directions on both labels say "No rinsing required." The Plus label says the product "generally dries within 2 hours and may take up to 24 hours depending on surface absorbency, temperature and [drying] conditions." Grout is the absorbent part of a shower, so expect the long end.

The shower is where the label runs thin. It says, "Reapply [Concrobium] if surfaces are washed or painted," and "Reapply weekly on hard surfaces." The Plus label adds that if a surface is to be cleaned, the product should be left "to work for 7 days" first. The labels list showers and bathroom tile as sites, but they do not say whether a daily shower counts as washing.

So here is the ruling for a shower. Treat it after the last shower of the day and leave it dry overnight. Do not scrub or clean the walls for a week if you use Plus. Then reapply at least weekly, as the label says, since daily water is the hardest case for a dry film. If spots come back sooner, that points to moisture, not a missed coat.

A worked case: one shower floor with gray grout

Take a 3 by 5 foot shower with white glazed wall tile and a gray porcelain floor. The grout is gray cement grout, unsealed. Black mildew spots sit in the floor corners and along the bottom row of wall joints.

Begin with the stain, since Concrobium will not lift it. The grout is colored, so start with oxygen bleach or 3 percent peroxide, not chlorine. Scrub, rinse well with clean water, and let the shower dry.

Next, decide how much to treat. Say you treat the floor (15 square feet) and the bottom 2 feet of the walls. The walls run 16 feet around, so that is 32 square feet more, or 47 in all.

Work out the amount. The Mold Control label gives 800 to 1,600 square feet per gallon. A gallon is 128 ounces, so 47 square feet takes roughly 4 to 8 ounces. A 32 ounce trigger bottle covers four to eight weekly coats.

Then apply it at night. Spray until the joints are evenly wet, wipe off drips on the tile face, and leave it. Do not shower until morning.

Suppose the spots come back in the same corners within a few days. That points to water staying in those joints, which a weekly film will not fix. Look at the slope, the caulk and the fan. Grout mold and mildew covers that check.

Change one fact and the answer shifts. If the grout were white, chlorine bleach would be the first step. If it were sealed, add a water drop test every few weeks, since the sealer maker says high-alkaline cleaners affect wear.

How strong is it next to the grout?

On the pH scale, 7 is neutral and higher numbers are more alkaline. Each whole step is ten times stronger.

Cement grout is alkaline itself. MAPEI's safety sheet for Keracolor S sanded grout (version 10, March 26, 2026) gives pH 11.00 for a 10 percent mix in water. Concrobium, at 11.1 to 11.5, sits just above that. The grout cleaner pH chart puts them side by side.

So Concrobium will not dissolve cement grout the way an acid can. The cautions are about sealer and colorant, which come next.

Grout by grout: where the makers draw the lines

Unsealed cement grout, any color. Yes, as a stop-growth film after the stain is gone. It has no bleach, so it does not lighten pigment. The Mold Control label allows porous masonry and concrete, and Rust-Oleum's page lists grout.

Sealed cement grout. Yes, with checks. Aqua Mix Sealer's Choice Gold (TDS-158) says, "Do not use cleaners containing ammonia, acids or bleach," and Concrobium has none of the three. The same sheet says "high-alkaline, acidic, or solvent-based cleaners will affect wear." So on a weekly schedule, do a water drop test more often.

Recolored grout. Not as a weekly habit. Aqua Mix Grout Colorant (TDS-173) says "high-alkaline, acidic or solvent-based cleaners will affect wear." See grout colorant.

Epoxy grout. Yes. LATICRETE's chart for SPECTRALOCK PRO Premium (DS-681.0-0217) rates 45 percent potassium hydroxide, a far stronger alkali, "R" (recommended) at 7 days. More in cleaning epoxy grout.

Natural stone tile. Only what the labels name. Mold Control lists "Sealed granite" and "Slate," and Plus lists sealed granite and sealed slate. Natural marble, limestone and travertine are not on either list. See grout for natural stone.

Concrobium on grout: what each label covers

Concrobium on grout, from the EPA labels for 82552-1 and 82552-3 and the grout and sealer makers' rules above
QuestionAnswerWhy
Does Mold Control kill mold in grout?No kill claim82552-1 label: "Fungistat" and "Mildewstat"; Pomerix: product type fungistat
Does it stop mold growing on grout?Yes, Mold Control's claim reaches porous surfaces82552-1: porous surfaces, "masonry," "concrete," "tile"; Rust-Oleum page lists grout
Does Plus kill mold in grout?No: hard non-porous only82552-3: kills "on hard, non-porous surfaces," 10 minutes wet; EPA 5813-85: "Grout is a porous surface"
Does Plus kill mold on glazed tile?Yes: 10 minutes wet82552-3 kill list: glazed ceramic and porcelain tile, sealed bathroom tile
Will it remove black stains?No: bleach or peroxide first, Concrobium lastBoth labels: will not "whiten stains"; "reapply Concrobium as a final step"
Rinse after spraying?No: let it dryLabels: "Allow treated surfaces to dry completely"; Plus: up to 24 hours
How often in a shower?At least weekly, and after washingLabels: "Reapply weekly," "Reapply ... if surfaces are washed"
Sealed or recolored groutSealed: yes, check sealer; recolored: not weeklyAqua Mix TDS-158 and TDS-173: high-alkaline cleaners "will affect wear"
Epoxy groutYesLATICRETE DS-681.0-0217: 45% KOH rated R at 7 days

Bottom line: Concrobium does not carry a kill claim for grout. Plain Mold Control is registered to stop mold growing, and its label allows porous surfaces, so it is the version for grout. Plus kills only on glazed tile and other non-porous surfaces. Remove the black stain first with bleach or peroxide, rinse and dry, then spray Concrobium on, let it dry, and reapply weekly.

How to use Concrobium on shower grout

  1. Remove the stain. Use bleach on white cement grout, or oxygen bleach or peroxide on colored grout. Concrobium will not whiten it.
  2. Rinse and dry. Rinse off the stain remover with clean water, then let the grout dry fully.
  3. Cover up. The label recommends an N-95 respirator, gloves and eye protection for mold areas under 30 square feet.
  4. Spray until evenly wet. Use it straight from the bottle. Do not dilute it.
  5. Wipe the tile face if drips might leave marks, but leave the joints wet.
  6. Let it dry. Do not rinse. Plus can take up to 24 hours on absorbent surfaces, so treat at night.
  7. Reapply weekly, and any time the surface has been washed.
  8. Dry the shower daily. Run the fan and squeegee the walls, since moisture is what brings mold back.

Concrobium, Tilex or RMR-86?

These three do different jobs. Tilex is a bleach spray with an EPA claim to kill mold on grout in 10 minutes, and it lightens stains. RMR-86 is bleach too, but has no EPA registration, so it is sold as a stain remover only. Concrobium kills nothing on grout and lifts no stains, but it is the only one of the three built to stay on the surface after it dries. For a shower that keeps growing spots, the usual order is a stain remover first, then Concrobium, then better drying. Cleaning shower grout covers the routine.

Where this answer stops applying

This page reads the EPA labels for 82552-1 (February 24, 2023) and 82552-3 (October 18, 2022). Rust-Oleum's technical data sheet is from 2019 and the safety sheets from 2011 and 2013. A newer label or a store bottle may print fewer claims than these master labels allow. Concrobium's aerosol, fogger and Mold Stain Remover are separate products and are not covered here. No source found tests Concrobium on grout itself, or measures how long its film lasts on a wall that gets wet every day, so this page gives no figure. Mold behind the tile, a musty smell with little to see, or soft or cracked grout all need more than a spray. The label says areas over 30 square feet "require special procedures and individuals trained in remediation."

Frequently asked questions

Is Concrobium safe on grout?

Yes on cement and epoxy grout. It has no bleach, acid or ammonia, and its pH of 11.1 to 11.5 is close to cement grout's own. On sealed grout, check the sealer more often, and do not use it weekly on recolored grout.

Does Concrobium Mold Control Plus kill mold on grout?

Not by its label. Plus claims to kill mold only on hard, non-porous surfaces, with 10 minutes wet contact, and EPA treats grout as porous. It does cover the glazed tile around the joints.

Do you rinse Concrobium off shower tile?

No. The label says to apply until evenly wet and let it dry completely, since the dried film is what stops growth. Wipe drips off the tile face if they might mark it.

Why is the black mold still there after Concrobium?

Because Concrobium does not whiten stains, and its label says so. Remove the stain with bleach on white grout or oxygen bleach or peroxide on colored grout, rinse and dry, then reapply Concrobium.

How often should you apply Concrobium in a shower?

The label says weekly, and again whenever the surface is washed. In a shower used every day, weekly is the minimum.

Is Concrobium bleach?

No. The active ingredient is sodium carbonate, about 1 percent, which is washing soda. The label says it contains no bleach, ammonia, alcohol or acid.

Sources and standards

Grout Atlas guidance is checked against ANSI A108/A118 and ISO 13007 requirements, the TCNA Handbook and manufacturer technical data sheets. Product formulations change, so confirm details on the current data sheet for the product you buy. Spotted an error? Report a correction.