Can You Use Murphy Oil Soap on Grout?

CleaningUpdated 11 min readHow we research

On this page
  1. What Murphy tells you to do on tile
  2. What is in the bottle: four safety data sheets
  3. "It contains lye and degrades grout": the claim checked
  4. The real risk: soap film in the joints
  5. What grout and sealer makers say
  6. Murphy or not: grout by grout
  7. Natural stone: the stone trade's own use
  8. How to clean a tile floor and its grout with Murphy
  9. Murphy, Fabuloso or Dawn on a tile floor?
  10. Where this answer stops applying
  11. Frequently asked questions
  12. Sources and standards

Yes. Murphy Oil Soap is safe on glazed ceramic and porcelain tile and on cement grout, sealed or not, at the dilution on the bottle: 1/4 cup in a gallon of warm water. Colgate-Palmolive's safety data sheets put it at pH 10.2 to 11.0, the same range as household ammonia and as cement grout itself, so it cannot dissolve the joint the way an acid does. The one instruction to ignore is "no rinsing required." Murphy is a true soap, not a detergent, and soap left in porous grout reacts with hard water into the film that holds dirt in the joints. Rinse with clean water.

Key takeaways

  • Murphy's own label lists "ceramic tile" and "no-wax floors" among its surfaces, at 1/4 cup per gallon (1/2 cup for heavy cleaning).
  • The current formula is water, sodium tallate (a soap made from tall oil fatty acids), propanediol, citronella oil, salt, tetrasodium EDTA and an amine oxide. No acid, ammonia or bleach.
  • pH on four Colgate sheets: 11.0 ± 0.6 (2002, 1% solution), 11.0 (2015), 10.2 (2020), 10.50 (2022). Cement grout measures 11.00 in MAPEI's own test.
  • The "it contains lye" claim comes from the May 2015 sheet, which lists sodium hydroxide at 1 to 5 percent. The August 2020 and March 2022 sheets for Murphy Oil Soap Liquid Original list no sodium hydroxide at all.
  • Tile makers ask for a "soapless" cleaner and a clear-water rinse. Murphy is soap, so the rinse matters more with it than with Dawn or Fabuloso.

What Murphy tells you to do on tile

Murphy's product page and bottle give one method for floors: "Dilute ¼ cup Murphy Oil Soap in 1 gallon of warm water," or 1/2 cup "For heavy cleaning," with a well wrung-out mop. "No rinsing required." The surfaces it names go beyond wood: "No-wax floors. Ceramic tile. Painted surfaces. Laundry stains. Cars. Leather. Vinyl." The label also says it "Does not contain ammonia or bleach."

Its one restriction is about wood: Murphy "should not be used on unfinished, unsealed, or waxed wood surfaces because they may be water sensitive." That "unsealed" refers to bare wood, not grout. The maker says yes to tile floors and so to their grout, and nothing about grout color, sealer, epoxy or stone.

What is in the bottle: four safety data sheets

The label lists "Water, Sodium Tallate, Propanediol, Cymbopogon Nardus (Citronella) Oil, Sodium Chloride, Tetrasodium EDTA, Lauramidopropylamine Oxide." Sodium tallate, CAS 61790-45-2, is registered as "Fatty acids, tall-oil, sodium salts." A sodium salt of fatty acids is what soap is: the "oil" is what the soap is made from, not oil left on the floor, and it puts Murphy with bar soap rather than with synthetic detergents like Dawn.

Colgate-Palmolive's safety data sheets agree on the pH and disagree on one line:

Murphy Oil Soap liquid on Colgate-Palmolive's own safety data sheets
SheetListed hazardous ingredientsClassificationpH
Murphy Oil Soap Liquid, MSDS (June 10, 2002)None listedNone; "Mild, multi-purpose cleaner"11.0 ± 0.6 (1% solution)
Wood Cleaner Liquid Original, 660000000228 v1.1 (May 31, 2015)Sodium hydroxide 1-5%, citronella oil 0.1-1%Skin irritant 2, eye irritant 2A, skin sensitizer 111.0
Liquid Original BDC, 660000002527 v1.4 (August 20, 2020)Geraniol 0.1-1%Skin sensitizer 1 only10.2
Liquid Original, 660000010906 v1.4 (March 23, 2022)Geraniol 0.1-1%Skin sensitizer 1 only10.50

The 2002 figure is measured on a 1 percent solution, and the label's 1/4 cup in a gallon (2 fluid ounces in 128) is about 1.5 percent, so it is close to mop-bucket strength. The 2015 and later sheets add "May cause an allergic skin reaction," from the fragrance oils; if your hands react, wear gloves.

"It contains lye and degrades grout": the claim checked

The claim traces to a 2017 thread on The Cleaning Standard forum, "Murphys Oil Soap on Tile." On December 17 a contractor relayed a customer email: "this Murphys 710 Soap over time is causing the grout to break (degrade) as well as the tile starting to wear at the edges." A member replied: "Don't know the percentage but it contains LYE which is corrosive." Three facts settle it.

  • One Colgate sheet does list lye. The May 31, 2015 sheet puts sodium hydroxide at ">= 1 - < 5" percent. That is the basis of every "contains lye" statement about Murphy.
  • The current sheets do not. The August 20, 2020 and March 23, 2022 sheets for Murphy Oil Soap Liquid Original list only geraniol at 0.1 to 1 percent, drop the skin and eye irritation classes, and no longer name sodium hydroxide on the Clean Water Act or state right-to-know lists where the 2015 sheet did. The retail ingredient list omits it too. Whether the 2015 line meant free lye or the lye used to make the soap, no Colgate sheet says, and this page does not guess.
  • Either way, the pH is the grout's own. MAPEI's Keracolor S sanded grout SDS (version 10, March 26, 2026) gives pH 11.00 for a 10 percent dispersion: "Cement gives a strong alkaline reaction with water." And Aqua Mix's Heavy-Duty Tile & Grout Cleaner (TDS-164, March 23, 2023), sold for tile and grout, is pH 11 to 12. A cleaner made for grout is more alkaline than Murphy.

What dissolves cement grout is acid, which attacks the calcium compounds binding the paste; that is why vinegar and Original Pine-Sol carry grout limits. On the grout cleaner pH chart, Murphy sits beside household ammonia (pH 11.2 to 11.5).

The thread itself offers a better explanation: the poster suspected "a soft tile, maybe Duraceramic, with putty like grout." DuraCeramic is a groutable vinyl set with its own premixed acrylic grout (see grout for vinyl tile), and nobody reported a test. Grout that breaks out of the joint usually has a mixing, curing or movement cause, covered in soft or crumbling grout.

The other "no" in search results is a catalog field: Hancock Lumber shows "Suitable for Grout: No" for Murphy's Multi-Use Wood Cleaner Spray (MUR01031), next to "Application: Wood." It is a different product, and the field is the store's, not Colgate's.

The real risk: soap film in the joints

This is where Murphy differs from the cleaners it is compared with. Penn State's outreach sheet on detergent and soap explains: hard water carries "calcium and magnesium ions," and "These ions bond with soap to make a greasy film that is called soap scum." Dawn and Original Fabuloso are synthetic detergents; sodium tallate is soap. Tile and stone makers write their care rules with this in mind:

  • Daltile: glazed ceramic and porcelain "can be cleaned with clear water and/or a pH neutral liquid cleaner (soapless). Follow with a clear water rinse and wipe dry to prevent film formation."
  • ARDEX (New Zealand): "Household soaps are not recommended as they can result in a buildup of soap scum."
  • Marble Institute of America: "an excessive concentration of cleaner or soap may leave a film and cause streaks." "Change the rinse water frequently."

Cement grout is porous and sits below the tile face, so mop water runs into the joints and leaves its soap there. Mopped weekly with no rinse, the joints turn gray and slightly greasy however often the floor is cleaned, the pattern described in cleaning floor grout. That is the likeliest real basis for the idea that Murphy "ruins" grout: it does not damage the joint, it coats it. "No rinsing required" suits a sealed wood floor. It does not suit a porous joint.

What grout and sealer makers say

No grout, sealer or tile maker found names Murphy, for or against. Their rules are about chemistry.

Sealed cement grout. Aqua Mix Sealer's Choice Gold (TDS-158) says "Do not use cleaners containing ammonia, acids or bleach." Murphy has none of the three. TDS-164 adds that "Regular use of high-alkaline cleaners will reduce sealer life," about its own pH 11 to 12 product; Murphy is just under that. So Murphy at label strength, rinsed, is fine on sealed grout, and the sealer maker's neutral cleaner is the better everyday product. The water drop test shows whether the sealer still works.

Recolored grout. Aqua Mix Grout Colorant (TDS-173) says "high-alkaline, acidic or solvent-based cleaners will affect wear." On recolored grout, use Murphy now and then, not as the weekly mop.

Epoxy grout. LATICRETE (DS-681.0-0217) asks for a neutral pH cleaner and warns its glow-in-the-dark DAZZLE version "might discolor from strong alkali cleaners and acids." Keep Murphy off glow grout; on ordinary epoxy grout no sheet gives a reason to avoid it, rinsed.

Metal trim and tile. The 2002 Colgate sheet says "Avoid prolonged contact with reactive metals (e.g., aluminum, brass, bronze, etc.)." Wipe aluminum or brass edge trim dry after mopping.

Murphy or not: grout by grout

Murphy Oil Soap at 1/4 cup per gallon, rinsed, on each grout and tile
SituationMurphy Oil Soap?Why
Glazed ceramic or porcelain, cement grout, sealedYes, diluted and rinsedNo ammonia, acid or bleach (TDS-158 rule); neutral cleaner is still the best routine choice
Glazed tile, cement grout, unsealedYes, diluted, and always rinsedpH at or below the grout's own; porous joints hold soap film
White or light groutYes, rinsed; never undilutedFilm and trapped soil show first on light joints
Recolored grout (colorant)Occasionally, dilutedAlkaline cleaners "affect wear" (TDS-173)
Epoxy groutYes; not on DAZZLE glow groutLATICRETE: glow grout may discolor from strong alkali
Groutable vinyl with acrylic groutYes at label dilutionMurphy lists vinyl; follow the floor maker's care sheet first
Marble, travertine, limestoneYes, diluted, rinsed and driedNo acid to etch; the Marble Institute allows "stone soap" and warns of film
Aluminum or brass trim, metal tileWipe dry after2002 sheet: avoid prolonged contact with reactive metals
Mildew, soap scum, hard waterNoNo kill claim; a soap adds to scum rather than removing it

Bottom line: Murphy Oil Soap will not degrade cement or epoxy grout. It is a pH 10.2 to 11 soap, about as alkaline as the grout itself, and the current Colgate sheets list no sodium hydroxide. Use 1/4 cup per gallon on glazed tile floors, then rinse with clean water even though the label says you need not, because soap left in porous joints turns to scum and holds dirt. On recolored grout, glow grout and freshly sealed floors, use it sparingly and keep a neutral cleaner for routine mopping.

Natural stone: the stone trade's own use

Stone restorers use Murphy. On the Stone and Tile Pros list in April 2018, Mike Marsoun wrote that "Murphys is VERY similar to HMK or any other stone soap," replying to a recommendation of the concentrate at "20 parts water to one part oil soap" for marble, travertine, limestone and onyx. The Marble Institute lists "stone soap" among acceptable stone cleaners. Murphy has no acid to etch calcareous stone, and its label strength (about 64 to 1) is gentler than the trade's 20 to 1. Rinse and dry stone as you would tile; see grout for natural stone.

How to clean a tile floor and its grout with Murphy

  1. Sweep or vacuum first, so the mop does not push grit into wet joints.
  2. Mix 1/4 cup in a gallon of warm water. Use 1/2 cup only for a heavily soiled floor, and only with a rinse.
  3. Mop with a well wrung-out mop, one section at a time, so water does not pool in the joints.
  4. Scrub dirty joints with a nylon grout brush dipped in the same solution. Never a wire brush.
  5. Rinse with clean, warm water in a second bucket, changing it when it clouds. In hard-water areas this step is what prevents scum.
  6. Dry and check. Grout that is still dark once dry has embedded soil or old residue; cleaning white grout covers the oxygen bleach step that comes next.

Do not mix Murphy with other cleaners. The 2002 sheet says to "Avoid contact with strong acids, alkalis and oxidizing and reducing agents." For white crust and shower film, use a product made for it, as set out in soap scum and hard water on grout.

Murphy, Fabuloso or Dawn on a tile floor?

All three are safe on grout. Original Fabuloso is a pH 7 detergent and Dawn a pH 9 detergent; Murphy is the most alkaline and the only true soap, which makes it good on grease ("removes dirt and grease," says its label) and the one most likely to leave scum in hard water. If the joints are gray from built-up film, switch routine mopping to a neutral, soapless cleaner, as Daltile asks. None of them kills mildew; grout mold and mildew covers what does.

Where this answer stops applying

It covers Murphy Oil Soap Original liquid in the U.S., at label dilution and rinsed. It does not cover undiluted product left to dry in pale joints, grout younger than its own cure time, grout inside a colorant's cure period, glow-in-the-dark epoxy, or other Murphy products such as the Orange Oil Spray and Squirt & Mop, whose sheets were not checked here. Grout that is already cracked, sandy or loose is a repair job, not a cleaning one.

Frequently asked questions

Does Murphy Oil Soap contain lye?

Colgate's May 2015 safety data sheet lists sodium hydroxide at 1 to 5 percent. Its August 2020 and March 2022 sheets for Murphy Oil Soap Liquid Original list no sodium hydroxide, and the retail ingredient list does not include it. Every sheet puts the product at pH 10.2 to 11, no more alkaline than cement grout.

Do I need to rinse Murphy Oil Soap off tile?

The label says no; tile makers say rinse after any cleaner. Daltile asks for a clear-water rinse "to prevent film formation," and Murphy is a soap, which forms scum with hard water. On grout, rinse every time.

Sources and standards

Grout Atlas guidance is checked against ANSI A108/A118 and ISO 13007 requirements, the TCNA Handbook and manufacturer technical data sheets. Product formulations change, so confirm details on the current data sheet for the product you buy. Spotted an error? Report a correction.