Can You Use Kaboom on Grout?
On this page
- Which Kaboom do you have?
- Four Kaboom bottles, four chemistries
- Kaboom Heavy Duty Shower, Tub & Tile: the acid one
- Kaboom Shower, Tub & Tile with OxiClean: the peroxide one
- Kaboom Foam-Tastic: the alkaline one
- The Kaboom bleach foam
- How to tell the bottles apart
- A worked case: one shower, three Kabooms
- Grout by grout: where the makers draw the lines
- Kaboom or not: grout by grout
- How to use Kaboom on grout
- Where this answer stops applying
- Frequently asked questions
- Sources and standards
It depends on which Kaboom, because the line runs from one end of the pH scale to the other. Kaboom Foam-Tastic is an alkaline foam at pH 12, and its maker points it at "grout lines." It is fine on cement and epoxy grout if you rinse. The Kaboom Shower, Tub & Tile spray sold today with OxiClean is a mild hydrogen peroxide cleaner, pH 3.0 to 3.5, fine on white and light grout. The Heavy Duty Shower, Tub & Tile is the one to watch. It is sulfamic acid at pH 0.8 to 1.2, the same acid as a grout haze remover. Keep it to white, unsealed, cured cement grout, and never use it on colored grout.
Key takeaways
- Kaboom is a brand, not a formula. Four Kaboom bathroom products sit at pH 1, 3, 12 and 12.5.
- The Heavy Duty Shower, Tub & Tile cleaner contains sulfamic acid, pH 0.8 to 1.2. Grout makers say no acid on colored joints, so use it on white grout only.
- The Shower, Tub & Tile spray "with the Power of OxiClean" is 3 percent hydrogen peroxide under EPA Reg. No. 10772-21. Its sheet gives pH 3.0 to 3.5, so it is a mild acid despite retail copy that says "no acid."
- Foam-Tastic is alkaline, pH 12, with no acid or bleach. Its label says "Do not use on acrylic, brass or unsealed granite or marble." Rinse it off grout.
- The Kaboom bleach foam is 0.8 to 2.72 percent sodium hypochlorite. Use it on white grout, and test colored grout first. Never use it right after the acid spray without a rinse.
Which Kaboom do you have?
Kaboom is a line of bathroom cleaners made by Church & Dwight, the company that also makes OxiClean and Arm & Hammer. Several Kaboom products share a name, and some have been renamed OxiClean. They do not share a chemistry. That is why advice about "Kaboom on grout" disagrees: each answer is about a different bottle.
Two terms decide the answer. pH is a 0 to 14 scale where 7 is neutral, below 7 is acid and above 7 is alkaline. Each whole step is ten times stronger than the last. Cement grout is the common sanded or unsanded grout mixed with water. It is porous, and its paste is made of cement, which acid dissolves and alkali does not. Wet cement grout is itself alkaline: MAPEI's sheet for Keracolor S sanded grout (version 10, March 26, 2026) gives pH 11.00. Colored grout is cement grout with pigment in it. The color sits in the thin paste at the face of the joint, so acid that eats paste takes color with it.
So the useful question is not "Kaboom or not" but "acid, alkali or bleach?" The table answers it from the makers' own documents.
Four Kaboom bottles, four chemistries
| Product (document, date) | Main cleaning ingredients | pH | Type |
|---|---|---|---|
| Kaboom Shower, Tub and Tile, MSDS-151B (February 18, 2010) | Sulfamic acid 1-6%, lauramine oxide 1-5% | 0.80-1.20 | Strong acid |
| Kaboom Shower, Tub and Tile; Kaboom Professional, SDS version 2.0 (November 24, 2015) | Sulfamic acid 1-5%, lauramine oxide 1-5% | 0.8-1.2 | Strong acid |
| Kaboom Shower, Tub & Tile Bathroom Cleaner, Heavy Duty, ingredient disclosure (March 12, 2024) | Sulfamic acid, lauramine oxide, alcohol ethoxylates | Not given | Acid |
| Kaboom Shower, Tub and Tile Cleaner, EPA Reg. No. 10772-21, SDS version 1.0 (May 19, 2020) | Hydrogen peroxide 1-5% (label: 3.00%), alkylbenzene sulfonic acid | 3.0-3.5 | Mild acid, peroxide |
| Kaboom Foam-Tastic with OxiClean, SDS version 2.0 (September 7, 2018) | Tetrasodium EDTA 1-5%, two surfactants 1-5% each, sodium hydroxide 0.1-1% | 12 | Alkali |
| Kaboom No-Drip Foam Mold & Mildew Stain Remover with Bleach, SDS version 2.0 (December 5, 2017) | Sodium hypochlorite 0.8-2.72%, sodium hydroxide 0.376-1.07% | 12.5 | Chlorine bleach |
The pH gap between the top and bottom rows is more than eleven steps. The grout cleaner pH chart places each one beside the other common cleaners.
Kaboom Heavy Duty Shower, Tub & Tile: the acid one
Church & Dwight's 2010 sheet lists sulfamic acid at 1 to 6 percent and gives "pH AS IS: 0.80-1.20." The 2015 sheet lists 1 to 5 percent, the same pH, and classes it Skin Corrosion 1A: "Causes severe skin burns and eye damage." The company's ingredient disclosure of March 12, 2024 still lists sulfamic acid for the Heavy Duty bottle, as a "pH adjuster." No sheet for the current Heavy Duty bottle gives a pH, but the ingredient list has not changed, so this page uses the 2015 figure.
Sulfamic acid is a dry acid sold in crystals for removing cement haze from new tile, so this spray is a haze remover in a bottle. Custom Building Products names the acid in its data sheet for Polyblend Plus grout (TDS-360, March 22, 2023). For haze that will not wipe off, it says to wash the tile "after ten days with Aqua Mix Sulfamic Acid Crystals, TileLab Sulfamic Acid Cleaner or Aqua Mix Cement Grout Haze Remover." It adds, "Perform a test in an inconspicuous area prior to complete application." A grout maker that sells this acid keeps it off its own grout for ten days.
No Kaboom label found warns about colored grout, so the rule comes from the grout makers. LATICRETE's data sheet for PERMACOLOR grout (DS-250-1026) says: "DO NOT use acid to clean colored grout joints." Lime-A-Way is the same acid at the same pH, and Reckitt's own sheet for it says not to use it on "coloured grout." The full case is on the Lime-A-Way on grout page. Aqua Mix's sealer sheet (TDS-158, March 23, 2023) says "Do not use cleaners containing ammonia, acids or bleach" on sealed grout.
The ruling: on white, unsealed cement grout between glazed tile, at least ten days old, the Heavy Duty spray is an occasional tool for hard water and soap scum. Spray, wait a short time, scrub and rinse well. It is a no on colored, sealed or recolored grout, and on any natural stone. The 2015 sheet also says "May be corrosive to metals," so wipe chrome and drains at once.
Kaboom Shower, Tub & Tile with OxiClean: the peroxide one
The trigger spray on most shelves now is a different product. Its EPA label (Reg. No. 10772-21, latest notification accepted November 2, 2026) lists one active ingredient: "Hydrogen Peroxide………3.00%." The label's brand list includes "KABOOM™ With the Power of OXICLEAN™ Stain Fighters Shower, Tub (and) (&) Tile Cleaner" and "OxiClean Shower, Tub, & Tile Bathroom Cleaner." It is a disinfectant, so the EPA has to accept its label.
Church & Dwight's 2020 sheet for it gives pH 3.0 to 3.5, and the retail ingredient list includes citric acid and alkylbenzene sulfonic acid. That makes it a mild acid, even though one retail listing says "No bleach, ammonia, or acid." The first two are true, but the third is not, by the maker's own sheet. Still, at pH 3.0 to 3.5 it is roughly 60 to 500 times weaker than the Heavy Duty spray.
The label's cleaning directions say: "For soap scum, apply to surface until thoroughly wet. Let product stand and penetrate soap scum [for 3 minutes]. Wipe clean with a damp cloth [or sponge] [and rinse with water]." It also says "Pre-test on an inconspicuous area for colorfastness," and "DO NOT USE on ... natural stone, natural marble, brass." Grout appears only in a marketing line: "Makes grout and hard surfaces look radiant." The disinfecting directions cover "Hard, non-porous surfaces" only. Grout is porous, so the spray cleans a joint but does not claim to disinfect it.
The ruling: yes on white or light cement grout and on epoxy grout, as the label directs. On colored grout it is still an acid, so do the label's colorfastness test on a hidden joint first, and do not make it a daily habit. On sealed grout, the same Aqua Mix acid rule applies. Use it now and then, not as the routine cleaner.
Kaboom Foam-Tastic: the alkaline one
Foam-Tastic is the aerosol that sprays blue and turns white, now sold as OxiClean Foam-Tastic. Church & Dwight's disclosure (March 7, 2024) lists "Kaboom™ Foam-Tastic™" as a synonym. Its 2018 sheet gives pH 12. The cleaning agents are tetrasodium EDTA, which grabs the minerals in hard water, two detergents and a little sodium hydroxide. Despite "OxiClean" on the can, neither the sheet nor the disclosure lists any peroxide or oxygen bleach, and it contains no acid or chlorine bleach.
The label reads: "Use On: Tubs, glazed ceramic tile, fiberglass, shower doors and vinyl curtains, sinks, counter tops and chrome fixtures." The directions say to wait until the foam turns white, then "wipe with a wet cloth or sponge and rinse with water." Then a note: "Do not use on acrylic, brass or unsealed granite or marble." OxiClean's own bathtub guide says Foam-Tastic is "the ideal solution you need to help clean vertical tile and grout lines."
The ruling: yes on cement grout, white or colored, and on epoxy grout, with the rinse the label asks for. At pH 12 it is one step above wet grout, and alkali does not dissolve cement paste the way acid does. The caution is sealer and colorant life. Aqua Mix TDS-158 says "high-alkaline, acidic, or solvent-based cleaners will affect wear" of the sealer. Its colorant sheet (TDS-173, February 28, 2023) says the same of recolored joints. On sealed or recolored grout, keep Foam-Tastic for the odd deep clean. The sheet also rates it "Causes serious eye damage," so do not spray it at face height without eye protection.
The Kaboom bleach foam
Kaboom's mildew product is the No-Drip Foam Mold & Mildew Stain Remover with Bleach. Church & Dwight now sells it as OxiClean Mold & Mildew Stain Remover with Bleach, under the same material number, 40500092. Its 2017 sheet lists sodium hypochlorite, which is chlorine bleach, at 0.8 to 2.72 percent, and gives pH 12.5.
OxiClean's guide gives the steps: "fully cover all mold and mildew stains. Wait for stains to disappear," then "Wipe away the clingy bleach foam with a wet sponge or cloth." It says not to use it on "clothes, fabric, wood, rubber, and painted or papered surfaces." On a porcelain tub, "rinse the foam off immediately after spraying to avoid pitting or discoloration."
Bleach on grout follows its own rules, set out on the bleach on grout page. Simple Green's grout page says "chlorine bleach will leach color out of tinted grout." TEC's Power Grout care bulletin (November 2025) says do not use bleach as a routine cleaner. So the foam is a yes on white or light grout, and a hidden-joint test first on colored grout. For color, oxygen bleach is the safer start.
How to tell the bottles apart
Read the label, not the brand name, because three lines on it settle the question.
- "Heavy Duty," or sulfamic acid in the ingredients: the acid one. Warnings about skin burns point the same way.
- "EPA Reg. No. 10772-21" and "Hydrogen Peroxide 3.00%": the peroxide spray. Kill claims for germs only appear on a bottle with an EPA number.
- "with Bleach" in the name: the bleach foam, or another Kaboom bleach product. The bleach rules apply to all of them.
An aerosol can that foams blue is Foam-Tastic.
A worked case: one shower, three Kabooms
Take a shower with white glazed wall tile and white cement grout, and a floor of small gray glazed porcelain mosaic with charcoal cement grout. None of the grout has been sealed, and it is two years old. There is hard water crust on the white wall joints, mildew dots in the floor corners, and a dull film over the whole floor. Under the sink are Kaboom Heavy Duty, Foam-Tastic and the Kaboom bleach foam.
Start with the floor film. The grout is charcoal, so the Heavy Duty spray is out by LATICRETE's acid rule. Foam-Tastic is alkaline and names glazed tile. Spray the floor, wait for the foam to turn white, scrub the joints with a nylon brush, and rinse with plenty of clean water.
Next, the wall crust. White, unsealed, two-year-old cement grout passes every test above. Spray the Heavy Duty on a small patch, let it work for a short time, scrub and rinse. If a shorter time does the job, use the shorter time. Wipe the chrome valve trim at once.
Now the mildew dots. Rinse the whole shower first, since the Heavy Duty spray is still in the wall joints and its sheet warns of "toxic fumes" with chlorinated products. On the charcoal floor grout, test the bleach foam on one joint near the drain. Let it dry before you judge, since wet grout looks darker. If the color holds, treat the spots and rinse, and if it fades, switch to oxygen bleach and see grout mold and mildew.
Change one fact and the answer shifts. If the floor grout were white, the Heavy Duty spray would be allowed there too. If the grout had been sealed, neither acid nor bleach would be routine. If the tile were marble, the peroxide label and the Foam-Tastic note would rule those two out, and the acid spray would be out as well.
Grout by grout: where the makers draw the lines
White or light cement grout between glazed tile. All four, with rules. Foam-Tastic and the peroxide spray for regular cleaning, rinsed. The bleach foam for mildew stains. The Heavy Duty acid for hard water now and then, never on grout younger than ten days. See grout cure time.
Colored cement grout. Foam-Tastic, rinsed. The peroxide spray after the label's hidden-joint test, and not daily. The bleach foam only after a test as well. The Heavy Duty acid: no, by LATICRETE DS-250-1026. If color has already gone patchy, fading grout explains why.
Sealed cement grout. Aqua Mix TDS-158 bans "ammonia, acids or bleach" and says high-alkaline cleaners affect wear. So the Heavy Duty spray is out, the bleach foam is not a routine cleaner, and the peroxide spray and Foam-Tastic are occasional. After any of them, do a water drop test.
Recolored grout. TDS-173 says "high-alkaline, acidic or solvent-based cleaners will affect wear." No Kaboom is a routine cleaner here. Use a neutral cleaner, as grout colorant explains.
Epoxy grout. LATICRETE's chart for SPECTRALOCK PRO Premium (DS-681.0-0217) rates 45 percent potassium hydroxide "R," recommended, even at 7 days. That covers Foam-Tastic. It also rates 5 percent citric acid R at 7 days. The peroxide spray lists citric acid and sits at pH 3, though the chart has no peroxide row. It rates 5 percent bleach R at 24 hours, far longer than the bleach foam stays on a joint. So both are fine for a short, rinsed use. The chart has no sulfamic acid row, so this page does not clear the Heavy Duty spray for epoxy, which does not need it anyway. The same sheet says the glow-in-the-dark DAZZLE additive "might discolor from strong alkali cleaners and acids." More in cleaning epoxy grout.
Natural stone tile. Foam-Tastic's label bans "unsealed granite or marble," and the peroxide label bans "natural stone, natural marble." Keep the acid spray off stone entirely: Reckitt's sheet for Lime-A-Way, the same acid, bans "natural marble, stone, terrazzo." No Kaboom bleach document found mentions stone, so this page does not rule on the bleach foam there. See grout for natural stone.
Kaboom or not: grout by grout
| Grout or surface | Foam-Tastic (pH 12) | Shower, Tub & Tile with OxiClean (peroxide, pH 3-3.5) | Heavy Duty (sulfamic acid, pH 0.8-1.2) | Bleach foam (pH 12.5) | Why |
|---|---|---|---|---|---|
| White or light cement grout, glazed tile | Yes, rinse | Yes | Occasional, cured 10+ days, rinse | Yes, rinse | Kaboom labels and sheets; Custom TDS-360: acid cleaners after ten days |
| Colored cement grout | Yes, rinse | Hidden test first, not daily | No | Hidden test first | LATICRETE DS-250-1026: no acid on colored joints; Simple Green: bleach leaches tint |
| Sealed cement grout | Occasional | Occasional | No | Not routine | Aqua Mix TDS-158: no acids or bleach; alkaline affects wear |
| Recolored grout | Not routine | Not routine | No | Not routine | Aqua Mix TDS-173: alkaline and acidic cleaners affect wear |
| Epoxy grout | Yes | Yes, short | Not cleared | Yes, short | LATICRETE DS-681.0-0217: KOH and citric R at 7 days, bleach R at 24 h; no sulfamic row |
| Natural stone or marble tile | No on unsealed | No | No | Not covered | Foam-Tastic and peroxide labels; Lime-A-Way sheet for sulfamic acid |
| Disinfecting the grout itself | Not claimed | Not claimed | Not claimed | Not claimed | EPA 10772-21: hard, non-porous surfaces only |
Bottom line: Foam-Tastic and the peroxide Shower, Tub & Tile spray are safe on most cement and epoxy grout if you follow the label and rinse. Test the peroxide spray first on colored grout. The bleach foam is for mildew on white grout. The Heavy Duty Shower, Tub & Tile is a sulfamic acid haze remover in a spray bottle: white, unsealed, cured cement grout only, and never with bleach.
How to use Kaboom on grout
- Read the back of the bottle. Find sulfamic acid, hydrogen peroxide, bleach or none of these. That decides which rules above apply.
- Open a window or run the fan. The acid, Foam-Tastic and bleach sheets all warn about eye damage or fumes.
- Rinse off any other cleaner first, above all bleach after acid or acid after bleach.
- Test a hidden joint on colored grout, and let it dry before you judge.
- Spray, then wait only as long as the label says. For Foam-Tastic, wait until the foam turns white. For the peroxide spray, up to 3 minutes on soap scum.
- Scrub the joint with a nylon brush, not a wire one.
- Rinse with plenty of clean water. Grout soaks up what dries in it. Hard water film that keeps coming back is covered in soap scum and hard water on grout.
Where this answer stops applying
This page covers the Kaboom sulfamic acid spray on its 2010 and 2015 sheets and its 2024 disclosure. It covers the peroxide spray on its 2020 sheet and EPA label of November 2026, Foam-Tastic on its 2018 sheet and current label, and the bleach foam on its 2017 sheet. No safety sheet could be found for older Kaboom bleach products sold under other names, such as StainBuster. Any Kaboom with bleach in its name falls under the bleach rules here. Formulas change, and the same name has carried both an acid and a peroxide, so the bottle in your hand decides. No Kaboom document addresses grout color or sealer, and no source measures how much grout one cleaning removes, so this page gives no figure. It does not cover premixed acrylic or urethane grout, which their makers' sheets govern, or grout that is cracked or crumbling, which needs repair. One rule holds on every surface: never mix the acid spray with the bleach foam or any other chlorine product, and keep air moving.
Frequently asked questions
Is Kaboom safe on grout?
Most Kaboom products are, used as labeled and rinsed. Foam-Tastic is alkaline and its maker recommends it for grout lines. The Heavy Duty Shower, Tub & Tile is sulfamic acid at pH 0.8 to 1.2, so keep it to white, unsealed, cured cement grout.
Does Kaboom have acid in it?
Some do: the Heavy Duty Shower, Tub & Tile lists sulfamic acid. The peroxide Shower, Tub & Tile spray lists citric acid and has a pH of 3.0 to 3.5. Foam-Tastic and the bleach foam are alkaline.
Can I use Kaboom on colored grout?
Foam-Tastic, yes, rinsed. The peroxide spray after a hidden-joint test. The Heavy Duty acid, no: LATICRETE says "DO NOT use acid to clean colored grout joints."
Does Kaboom Foam-Tastic contain bleach or OxiClean?
Neither its 2018 safety sheet nor Church & Dwight's 2024 ingredient list shows any chlorine bleach, peroxide or oxygen bleach. "OxiClean" on the can is a brand name, and the cleaning agents are EDTA, detergents and a little sodium hydroxide.
Can Kaboom remove grout haze?
The Heavy Duty spray uses the same acid as sulfamic haze removers, but a grout maker waits ten days before acid on its grout. For haze, follow how to remove grout haze rather than a bathroom spray.
Can I mix Kaboom with bleach?
No. The acid spray's sheet says "Do not mix with chlorinated or sanitizing products as toxic fumes may be released." Rinse between products.
Sources and standards
- Church & Dwight, Kaboom Shower, Tub and Tile, MSDS-151B (February 18, 2010)
- Church & Dwight, Kaboom Shower, Tub and Tile; Kaboom Professional Shower, Tub and Tile with OxiClean Stain Fighter, safety data sheet version 2.0 (November 24, 2015)
- Church & Dwight, product ingredient disclosures: Kaboom Shower, Tub & Tile Bathroom Cleaner, Heavy Duty (March 12, 2024); OxiClean Foam-Tastic, Fresh Scent (March 7, 2024); OxiClean Mold & Mildew Stain Remover with Bleach (March 26, 2024)
- Church & Dwight, Kaboom Shower, Tub and Tile Cleaner, EPA Reg. No. 10772-21, safety data sheet version 1.0 (May 19, 2020)
- US EPA, EPA Reg. No. 10772-21 label notification (accepted November 2, 2026)
- Church & Dwight, Kaboom Foam-Tastic with OxiClean, safety data sheet version 2.0 (September 7, 2018)
- Church & Dwight, Kaboom No-Drip Foam Mold & Mildew Stain Remover with Bleach, safety data sheet version 2.0 (December 5, 2017)
- Stop & Shop product listings with label text: OxiClean Foam-Tastic; OxiClean Bathroom Cleaner trigger spray
- True Value, OxiClean 32 oz. Shower Tub & Tile Bathroom Cleaner listing, the "No bleach, ammonia, or acid" claim checked above
- OxiClean, How do you clean a bathtub
- LATICRETE, PERMACOLOR Grout, DS-250-1026; SPECTRALOCK PRO Premium Grout, DS-681.0-0217
- Custom Building Products, Polyblend Plus Sanded Grout, TDS-360 (March 22, 2023), Aqua Mix Sealer's Choice Gold, TDS-158 (March 23, 2023) and Aqua Mix Grout Colorant, TDS-173 (February 28, 2023)
- Reckitt Benckiser, Lime-A-Way Cleaner (Sprayer) material safety data sheet #19921 (May 12, 2010)
- MAPEI, Keracolor S safety data sheet, version 10 (March 26, 2026)
- TEC Specialty Products, Power Grout: Cleaning and Maintenance (November 2025)
- Simple Green, How to clean grout
Grout Atlas guidance is checked against ANSI A108/A118 and ISO 13007 requirements, the TCNA Handbook and manufacturer technical data sheets. Product formulations change, so confirm details on the current data sheet for the product you buy. Spotted an error? Report a correction.