Can You Use Krud Kutter on Grout?

CleaningUpdated 16 min readHow we research

On this page
  1. What Krud Kutter is, and what "alkaline" means here
  2. What the Krud Kutter sheets say
  3. Which pH is right: 12.2 or 13.5?
  4. Is Krud Kutter phosphoric acid? The claim checked
  5. What Krud Kutter's directions say
  6. A worked case: latex paint drips on a tile floor
  7. Grout by grout: where the makers draw the lines
  8. In the shower: the Mold & Mildew Stain Remover
  9. Krud Kutter or not: grout by grout
  10. How to clean grout with Krud Kutter
  11. Krud Kutter, TSP or oven cleaner?
  12. Where this answer stops applying
  13. Frequently asked questions
  14. Sources and standards

Yes, on cement grout, as a short spot job. Krud Kutter's own data sheet lists "tile and grout" among the jobs for the full-strength cleaner. It also says: "Always test on an inconspicuous area first." Krud Kutter Original is a strong alkaline degreaser, not an acid, so it does not dissolve cement grout the way acid does. Its newest safety data sheet puts it at pH 12.5 to 13.5. That is strong enough to wear down sealer and colorant. The sheet also says it "slowly corrodes copper, aluminum, zinc, and galvanized surfaces." So test it, leave it a few minutes at most, and rinse it off. Keep it off metal trim, sealed or recolored grout you want to keep, and natural stone.

Key takeaways

  • Krud Kutter Original (Rust-Oleum safety data sheet, July 9, 2024) is a detergent with sodium metasilicate 1 to 2.5 percent and potassium hydroxide 0.1 to 1 percent. Its pH is 12.5 to 13.5. There is no acid in it.
  • The older technical data sheets (2021 US, 2022 Canada) say pH "<12.2." The 2024 sheet changed Section 9, where pH lives. Go by the newer, higher figure.
  • Cement grout is about pH 11 (MAPEI Keracolor S: 11.00). Krud Kutter is stronger, so the risk is to sealer, colorant and metal, not the cement. Short dwell and a rinse handle it.
  • Phosphoric acid is in Krud Kutter's etch and rust products, not in the Original cleaner. Concrete Clean & Etch is pH under 1.5. Do not use those on grout.
  • For mildew stains in a shower, Krud Kutter makes a separate Mold & Mildew Stain Remover at pH 10 to 11, with no bleach. Its sheet admits it may not clear stains in "old grout or silicone caulking."

What Krud Kutter is, and what "alkaline" means here

Krud Kutter is a brand of cleaners made by Rust-Oleum. Most people mean the yellow-label bottle: Krud Kutter Original Cleaner/Degreaser & Stain Remover. It is sold in paint aisles because painters use it to clean walls before painting and to lift dried latex paint. That is the product this page rules on.

It is an alkaline degreaser. That means two things. It has a high pH, so it sits on the alkaline side of the scale, the opposite of acid. And it is built to break down grease and oily soil, which alkalis do well. On the pH scale, 7 is neutral. Below 7 is acid, like vinegar. Above 7 is alkaline, like ammonia or lye. Each whole step is ten times stronger than the one before it.

Two ingredients make Krud Kutter alkaline. Potassium hydroxide is a strong alkali, sometimes called potash lye. Sodium metasilicate is an alkaline salt used in heavy cleaners. The cleaning itself is done by a surfactant, the soap-like part that lets water lift grease.

That matters for grout because cement grout is alkaline too. Acid dissolves it. An alkali does not dissolve it the same way. But a strong alkali does wear the layers that sit on top of a joint: the sealer and any colorant. The grout cleaner pH chart sets every common cleaner on one scale.

What the Krud Kutter sheets say

A safety data sheet (SDS) is the maker's legal record of what is in a product. Section 3 lists the hazardous ingredients, and Section 9 gives the pH. A technical data sheet (TDS) is the maker's how-to-use sheet. Here is what each one found says, including the brand's acid products, since those are where the confusion starts.

Krud Kutter products on Rust-Oleum's and Krud Kutter's own sheets
Product (sheet, date)Listed ingredientspHOn grout
Krud Kutter Original Cleaner & Degreaser, SDS WPS1808340 (July 9, 2024)Fatty alcohol ethoxylate 1-2.5%, sodium metasilicate 1-2.5%, potassium hydroxide 0.1-1%12.5-13.5Yes on cement grout: test, short dwell, rinse
Krud Kutter Original, US TDS KRK-01 (rev. 020121)"Proprietary Blend of Biodegradable Surfactants, Detergents and Emulsifiers"<12.2Lists "tile and grout" under full-strength heavy cleaning
Krud Kutter Original, Canada TDS KRK-88 (rev. 032122)Same wording; label panel: "Contains ethoxylated alcohols and sodium metasilicate"<12.2Same "tile and grout" line
Krud Kutter Mold & Mildew Stain Remover, TDS KRK-52 (rev. 120721)"Proprietary Ingredients in a Water-based Solution," no bleach10-11Lists "tile & grout"; the shower choice
Krud Kutter Concrete Clean & Etch, TDS KRK-17 (rev. 112921)"Phosphoric Acid and Proprietary Ingredients"<1.5No: an acid etch for concrete
Krud Kutter HP The Must for Rust, SDS (August 5, 2024)Phosphoric acid 10-25%1.0-3.0No: a rust remover
Krud Kutter Metal Clean & Etch, MSDS (June 8, 2011)Phosphoric acid under 40%Not givenNo: a metal etch

The Original's 2024 sheet rates it a skin irritant (Category 2) and an eye irritant (Category 2B). Its toxicology section is blunter: "Substance is corrosive. Causes severe skin burns." It asks for gloves and eye protection. Section 10 lists strong acids among the things it must not meet, and it says the product "slowly corrodes copper, aluminum, zinc, and galvanized surfaces."

Which pH is right: 12.2 or 13.5?

The two sheets for the Original disagree. Both technical data sheets, US (2021) and Canada (2022), say pH "<12.2." The safety data sheet revised July 9, 2024 says 12.5 to 13.5. Its revision note says why it changed: "Substance and/or Product Properties Changed in Section(s): 09 - Physical & Chemical Properties." Section 9 is where pH lives.

So the newer sheet is the one to use. It is also the safer reading. If you plan for pH 13.5 and the bottle is 12, you have lost nothing. If you plan for 12 and the bottle is 13.5, you have used a cleaner up to 30 times stronger than you thought.

Now set it beside the grout. MAPEI's safety data sheet for Keracolor S sanded grout (version 10, March 26, 2026) gives pH 11.00 for a 10 percent mix in water. It says "Cement gives a strong alkaline reaction with water." Krud Kutter straight from the bottle is 1.5 to 2.5 steps above that, about 30 to 300 times as alkaline.

The closest product sold just for grout is Aqua Mix Heavy-Duty Tile & Grout Cleaner. Its sheet (TDS-164, March 23, 2023) gives "11-12 (alkaline)," and you dilute it 1 part to 2 to 5 parts water. Even so, the same sheet warns: "Regular use of high-alkaline cleaners will reduce sealer life." It also says it "May adversely affect grout joints that have been coated with colorant or grout stain." Neat Krud Kutter is stronger than that cleaner, so the same limits apply to it, only more so.

Is Krud Kutter phosphoric acid? The claim checked

Ask a search engine whether Krud Kutter is an acid, and the answer that comes back often says yes: its active ingredient is phosphoric acid. That is true of some Krud Kutter products. It is not true of the one most people have under the sink.

Search results mix the brand's sheets together, and the brand makes both kinds of product. Concrete Clean & Etch says "WARNING: CONTAINS PHOSPHORIC ACID" and gives pH under 1.5. The Must for Rust lists phosphoric acid at 10 to 25 percent. Metal Clean & Etch lists it under 40 percent. Read one of those sheets, and "Krud Kutter is phosphoric acid" looks settled.

The Original's sheet lists no acid at all. Its three listed ingredients are a surfactant and two alkalis, and its pH is 12.5 to 13.5. It even lists "strong acids" as incompatible. The two families sit at opposite ends of the pH scale.

The mix-up matters because the right advice flips. An acid at pH under 1.5 dissolves the cement in grout. Concrete Clean & Etch is built to do exactly that to concrete: its sheet says it "creates a porous surface." On grout, that is erosion. The pages on muriatic acid and Lime-A-Way show what acid does to a joint. The Original carries the opposite risk: it is too alkaline for sealer and metal, not for the cement.

So read the label before you spray. "Clean & Etch," "Rust" or "phosphoric acid" means keep it off grout. "Original Cleaner/Degreaser" is the alkaline one.

What Krud Kutter's directions say

The US data sheet gives three strengths:

  • Heavy cleaning, full strength: for grills, ovens, "tubs, sinks and showers," "tile and grout," driveways and floor wax.
  • All purpose, 1½ cups to 1 gallon of water: for appliances, porcelain, linoleum, vinyl, walls, and metals including chrome, copper and aluminum.
  • Reflective surfaces, 1½ ounces to 1 gallon: glass, mirrors, screens.

The method is short: "Always test on an inconspicuous area first. Apply directly on surface to be cleaned and allow to penetrate briefly. Wipe off with a clean cloth or towel." For harder jobs: "allow to stand for a few minutes before wiping dry." For dried latex paint: "scrub with a brush or scouring pad and wipe off with a wet rag."

Its pressure-washer section adds the rule that matters most for a porous joint: leave it "3 to 5 minutes to penetrate. Do not allow product to dry on surface." That is the line forum tips skip. A 2019 Hometalk answer says: "Use Krud Kutter, let soak and then rinse off." The rinse is right. A long soak is not what the sheet says.

The sheet says the cleaner "leaves no residue." But grout is porous. It soaks up liquid, and whatever dries in it stays there. So treat the wipe-off step as a rinse: clean water, then pick it up. Grout porosity and absorption explains why the joint holds what you put on it.

The data sheet allows the all-purpose mix on aluminum and copper. The safety sheet says the product corrodes those metals. Both can be true: one is about a mix of about 1 part to 11, wiped off, and the other is about the product itself. So keep neat Krud Kutter off metal, and rinse any splash.

A worked case: latex paint drips on a tile floor

It is a real question. A Florida caller to The Money Pit in 2011 said her husband was using Krud Kutter on paint that had got on their tile when the woodwork was painted. On the tile, "it actually works pretty well," she said.

So take the job Krud Kutter is best known for. Someone has painted the baseboards in a kitchen with glazed ceramic floor tile and beige cement grout, never sealed. Drips of latex paint have dried on the tile and in the joints along the wall. Where the kitchen meets the hall there is a metal transition strip, and it may be aluminum.

Start with the label. Dried latex paint is the job it names, and tile and grout are on its full-strength list. So the product is on-label here.

Next, the grout. It is bare cement, about pH 11 itself. Krud Kutter at 12.5 to 13.5 is stronger, but it is an alkali, so it will not eat the cement the way an acid would. With no sealer and no colorant, there is no top layer to wear.

Then the test. Pick a joint behind the fridge or in a closet. Apply a little, wait the "few minutes" the label allows, scrub with a nylon grout brush, rinse with clean water, and let it dry. Look at it the next day for any change in color.

If the test joint looks the same, work the drips in short sections. Apply, wait a few minutes, scrub, rinse, and pick up the water with a sponge or towel. Do not let it dry in the joint. Wear gloves and glasses. The SDS asks for both.

Now the strip. Neat cleaner should not sit on it. Mask it with tape, or wipe and rinse any splash at once.

Change one fact and the answer changes. If the grout had been sealed last year, the job is still fine as a one-off. Check it afterward with a water drop test. If the joints had been recolored with a colorant, use a milder cleaner on them. If the floor were marble, use a stone cleaner and leave Krud Kutter in the garage.

Grout by grout: where the makers draw the lines

Unsealed cement grout. Yes, as above. Krud Kutter lists tile and grout, and the cement is alkaline itself. Test, keep the dwell short and rinse.

Sealed cement grout. Occasional spot use only, then check the sealer. Aqua Mix Sealer's Choice Gold (TDS-158, March 23, 2023) names "high-alkaline, acidic, or solvent-based cleaners" among the things that "will affect wear." For routine mopping, the same sheet asks for a neutral cleaner. See how often to seal grout.

Recolored grout. Keep it off. Aqua Mix Grout Colorant (TDS-173, February 28, 2023) uses the same "high-alkaline" warning. TDS-164 says even its own pH 11 to 12 cleaner "May adversely affect" colorant. See grout colorant.

Epoxy grout. Yes for a spot clean. LATICRETE's chart for SPECTRALOCK PRO Premium grout (DS-681.0-0217) rates 45 percent potassium hydroxide "R," resistant. That is the same alkali Krud Kutter lists at 1 percent or less. LATICRETE still asks for a neutral cleaner for routine care. It also warns that its glow-in-the-dark SPECTRALOCK DAZZLE "might discolor from strong alkali cleaners," so keep Krud Kutter off that. More in cleaning epoxy grout.

Natural stone. No. Daltile's care guide says stone is "porous by nature" and that "many of the cleaners acceptable for use on ceramic tile can stain, damage or dull stone." It asks for "cleaners specifically designed for cleaning stone," which it describes as "concentrated neutral pH cleaners." Krud Kutter is the opposite of neutral. See grout for natural stone.

Metal trim and fittings. Keep neat cleaner off. Many tile edge trims and transition strips are aluminum, and some are brass or galvanized steel. Grout or caulk at Schluter trim covers how those profiles meet the joint.

In the shower: the Mold & Mildew Stain Remover

Krud Kutter's data sheet lists "soap scum mildew stains" among the jobs for the Original. But for a shower, the brand sells a milder product made for it: Krud Kutter Mold & Mildew Stain Remover.

Its data sheet (KRK-52, rev. 120721) says it works "without the use of bleach or other harsh chemicals." It lists "tile & grout, tubs, shower doors, vinyl curtains" and gives pH 10 to 11, about the same as cement grout. Its method: "Always test on an inconspicuous area first," spray from 6 to 8 inches, "allow to sit 5 minutes," then "Rinse or wipe clean."

The same sheet admits a limit most labels do not: "You may not be able to remove stains from mold and mildew embedded in hard water deposits, old grout or silicone caulking." That is honest. A dark stain deep in old grout or caulk may not lift with any surface spray. For those, see grout mold and mildew, which covers bleach on white grout, oxygen bleach on colored grout, and when caulk has to be cut out.

Krud Kutter or not: grout by grout

Krud Kutter on grout, from Rust-Oleum's sheets and grout, sealer and tile makers' rules above
Grout and jobUse Krud Kutter Original?Why
Unsealed cement grout, glazed tile: grease, paint drips, ground-in dirtYes: test, a few minutes, scrub, rinseTDS KRK-01 lists "tile and grout"; alkali, not acid; grout pH 11.00 (Keracolor S)
Sealed cement groutSpot use only, then water drop testHigh-alkaline cleaners "will affect wear" (TDS-158) and "reduce sealer life" (TDS-164)
Recolored grout (colorant)NoTDS-173 high-alkaline warning; even pH 11-12 cleaner "May adversely affect" colorant (TDS-164)
Epoxy groutYes for spots; neutral for routine45% KOH rated R (LATICRETE DS-681.0-0217)
Glow-in-the-dark epoxy (DAZZLE)No"might discolor from strong alkali cleaners" (LATICRETE)
Natural stone tileNoDaltile: stone cleaners only, "concentrated neutral pH cleaners"
Joints beside aluminum, copper, zinc or galvanized trimKeep neat cleaner off the metal; rinse splashes"slowly corrodes copper, aluminum, zinc, and galvanized surfaces" (SDS 2024)
Mildew stains in a showerUse the Mold & Mildew Stain Remover insteadpH 10-11, no bleach, lists tile and grout (KRK-52)
Krud Kutter Clean & Etch or rust productsNever on groutPhosphoric acid, pH under 1.5 to 3.0 (KRK-17, The Must for Rust SDS)

Bottom line: Krud Kutter Original is safe on bare cement grout and epoxy for a short spot clean. It is a strong alkali at pH 12.5 to 13.5, not an acid, so it will not dissolve the joint. Test first, leave it a few minutes, scrub with a nylon brush and rinse. Keep it off sealed or recolored grout as a routine, off stone and off metal trim. In the shower, use the Mold & Mildew Stain Remover. Never use the Krud Kutter etch or rust products on grout: those are the phosphoric acid ones.

How to clean grout with Krud Kutter

  1. Check the bottle. It must say Original Cleaner/Degreaser. If it says Clean & Etch, Rust or phosphoric acid, stop.
  2. Check the tile, grout and trim. Glazed ceramic or porcelain with cement or epoxy grout is fine. Natural stone, recolored grout or glow grout is not. Tape off metal strips.
  3. Put on gloves and glasses, and open a window.
  4. Test a hidden joint. Apply, wait a few minutes, scrub, rinse, and look at it when dry.
  5. Work in small sections. Spray full strength on the soiled joints, or mix 1½ cups per gallon for light dirt over a wider area.
  6. Wait a few minutes, no more. Do not let it dry in the joint.
  7. Scrub with a nylon grout brush. Never a wire brush.
  8. Rinse with clean water and pick it up with a sponge, towel or wet vacuum. Rinse twice where it was used full strength.
  9. Never mix it with another cleaner, least of all an acid. The SDS lists strong acids as incompatible. Rinse before anything else goes on.

For grease that keeps coming back in front of a stove, grease and food stains on grout covers the next steps.

Krud Kutter, TSP or oven cleaner?

All three are strong alkalis, and none is an acid. TSP is pH 11 to 12 and comes as a powder you dissolve, with a box method that ends in a rinse. Krud Kutter Original is stronger, at 12.5 to 13.5, but it is sold ready to use and its data sheet names tile and grout. Oven cleaner reaches pH 13.3 to 14, and its label leaves grout off the list. For routine mopping, none of them is the right tool. A mild cleaner like Mr. Clean at pH 10.3 does that job.

Where this answer stops applying

This page covers Krud Kutter Original Cleaner/Degreaser & Stain Remover on the 2024 SDS and the 2021 and 2022 data sheets above, and the Mold & Mildew Stain Remover on its 2021 sheet. Other Krud Kutter cleaners were not checked for grout, including Kitchen Degreaser, Tough Task Remover, Multi-Purpose House Wash and Gloss-Off. Products sold under the Krud Kutter name outside North America may have other formulas, so read the sheet for yours. No source found measures how much sealer one Krud Kutter wash removes, so this page gives no figure. It does not rule on premixed acrylic or urethane grout, or on grout younger than its cure time; their makers' care sheets govern. Grout that is already soft, sandy or cracked has a cause other than cleaning. Krud Kutter will not fix it, and scrubbing may loosen more. The skin and eye warnings apply whatever the surface: the SDS says the product "Causes severe skin burns," so gloves and eye protection are not optional.

Frequently asked questions

What is the pH of Krud Kutter Original?

pH 12.5 to 13.5 on the safety data sheet revised July 9, 2024. Older technical data sheets from 2021 and 2022 say under 12.2. The newer sheet changed its Section 9, so use 12.5 to 13.5.

Does Krud Kutter contain phosphoric acid?

Krud Kutter Original does not. Its sheet lists a surfactant, sodium metasilicate and potassium hydroxide. Krud Kutter Concrete Clean & Etch, The Must for Rust and Metal Clean & Etch do contain phosphoric acid.

Will Krud Kutter damage grout?

Not sound cement or epoxy grout used briefly and rinsed, because it is an alkali, not an acid. It can wear sealer and colorant, and it can discolor glow-in-the-dark epoxy, so keep it off those as a routine.

Does Krud Kutter remove grout sealer?

No source measures it. Sealer makers say high-alkaline cleaners "will affect wear," and Krud Kutter is high-alkaline. After using it on sealed grout, do a water drop test and reseal if water soaks in.

Can I use Krud Kutter on shower grout?

The Original lists tubs and showers, but chrome and metal fittings are close by and the grout is often sealed. The Mold & Mildew Stain Remover is made for showers, at pH 10 to 11 with no bleach. See cleaning shower grout.

Do I need to rinse Krud Kutter off tile?

The sheet says wipe it off and do not let it dry. On grout, rinse with clean water as well, since the joint is porous and holds what dries in it.

Sources and standards

Grout Atlas guidance is checked against ANSI A108/A118 and ISO 13007 requirements, the TCNA Handbook and manufacturer technical data sheets. Product formulations change, so confirm details on the current data sheet for the product you buy. Spotted an error? Report a correction.