Can You Use Mr. Clean on Grout?

CleaningUpdated 16 min readHow we research

On this page
  1. What Mr. Clean liquid is, and what pH means
  2. What is in the bottle: five sheets from 2008 to 2025
  3. Why pH 10.3 cannot hurt sound grout
  4. What the label says to do, and the line that matters
  5. The sticky floor: what the complaints are really about
  6. A worked case: dark joints in a bathroom traffic lane
  7. Why Mr. Clean's own grout page skips the liquid
  8. Sealed grout: dilute for routine, neat for spots
  9. Epoxy grout, natural stone and metal trim
  10. The Mr. Clean bathroom spray is an acid
  11. Mr. Clean or not: grout by grout
  12. How to clean grout with Mr. Clean
  13. Mr. Clean, Murphy Oil Soap or Swiffer?
  14. Where this answer stops applying
  15. Frequently asked questions
  16. Sources and standards

Yes. Mr. Clean Multi-Surface Cleaner is safe on cement and epoxy grout, and its safety data sheets show why. They put the liquid at pH 10.3, with a mild detergent and no acid, bleach or ammonia. That is a shade less alkaline than cement grout itself, so it cannot dissolve a joint. For a floor, use the label's 1/8 cup in a gallon of water. For dirty joints, the label says to pour it straight on a sponge, then "Wipe and rinse." That rinse is the step people skip, and it is why some floors feel sticky afterward.

Key takeaways

  • The newest sheet, Mr. Clean Multi-surface Cleaner Ocean (revision 1, April 11, 2025), gives pH 10.3. A 2008 sheet and a 2023 Lemon sheet give the same 10.3. A 2015 Febreze Meadows & Rain sheet gives 11.0.
  • Cement grout is itself alkaline: MAPEI gives pH 11.00 for its Keracolor S grout in water. Mr. Clean is no stronger an alkali than the joint it cleans.
  • For floors, Mr. Clean says "Mix 1/8 cup per 1 gallon" and "Usually no need to rinse." For tough soil, it says pour it on and "Wipe and rinse." Grout joints are tough soil, so rinse them.
  • Mr. Clean's own grout page recommends a Magic Eraser, not the liquid. The eraser is an abrasive and the liquid is not, so try the liquid and a brush first.
  • Keep it off natural stone, and off aluminum or copper trim. The label rules out "copper or aluminum surfaces," and Daltile wants stone cleaned with neutral stone cleaners.

What Mr. Clean liquid is, and what pH means

This page is about the liquid in the big bottle: Mr. Clean Multi-Surface Cleaner, also sold as Mr. Clean All Purpose Cleaner. It comes in scents like Ocean, Lemon, Febreze Meadows & Rain and Gain Original. It is not the Magic Eraser, which is a foam block, and it is not the Mr. Clean bathroom spray, which is a different formula (more on that below).

The cleaning agent is a surfactant. That is the part of any soap or detergent that lets water grab grease and lift it off a surface. Mr. Clean's main one is an alcohol ethoxylate, a nonionic surfactant, which means it carries no electric charge. In practice that makes it a mild grease cutter, from the same family of ingredients found in many dish and floor cleaners.

A pH number says how acidic or alkaline a liquid is. The scale runs from 0 to 14, and pure water sits at 7, which is neutral. Below 7 is acid and above 7 is alkaline. Each whole step is ten times stronger than the one before it.

That scale matters for grout because cement grout is built from alkaline cement. An acid attacks it, while an alkali at or below the grout's own pH does not. So the question "will it hurt my grout?" mostly comes down to two things: is it an acid, and does it leave anything behind in the joint? Grout cleaners by pH lays out the whole scale.

What is in the bottle: five sheets from 2008 to 2025

Procter & Gamble, which makes Mr. Clean, publishes a safety data sheet for each formula. Section 3 lists the hazardous ingredients and Section 9 gives the pH. Here is every sheet found:

Mr. Clean liquid formulas, from Procter & Gamble's own safety data sheets
Sheet and dateListed ingredientspH
Mr. Clean Multi-Surfaces, MSDS RQ0805372 (February 4, 2008): Spring Garden, Invigorating Breeze, Sparkling Apple, Ultimate OrangeAlcohol ethoxylates 3-7%10.3 (neat)
Mr. Clean Multi-Purpose Cleaner with Febreze Freshness, Meadows & Rain, 97086254 (April 29, 2015)"Hazardous ingredients: None"11.0
Mr. Clean Multi surface cleaner, Lemon, 2x concentrated, 20113886 (August 30, 2023)Alcohol ethoxylates 1-5%, citronellol (a scent oil) 0.1-1%10.3
Mr. Clean Multi-surface Cleaner, Ocean, 21315224 (revision 1, April 11, 2025)Alcohol ethoxylates 1-5%, dipropylene glycol butoxy ether (a mild solvent) 0.5-1.5%10.3
Mr. Clean Disinfecting Bath Cleaner with Febreze Freshness, Meadows & Rain, 92332881 (April 30, 2015)Citric acid 1-5%, sodium lauryl sulfate 1-5%, dipropylene glycol butoxy ether 1-5%3.0

The first four are the multi-surface liquid, and across seventeen years they sit at pH 10.3 to 11.0. None lists an acid, chlorine bleach or ammonia. The 2008 sheet gives the label's own ingredient line: "Cleaning agents (anionic and nonionic surfactants), quality control agents, perfume, colorant and water."

The hazard ratings are mild. The 2025 Ocean sheet has just one: "Causes serious eye irritation." The 2023 Lemon sheet has a milder one: "Causes eye irritation." The 2015 Febreze sheet says "Not Classified." Both newer sheets list "Incompatible Materials: None in particular."

The fifth row is the outlier. The Disinfecting Bath Cleaner is a Mr. Clean product too, but it is a citric acid spray at pH 3.0, not the liquid this page rules on. See the bath cleaner section below.

Why pH 10.3 cannot hurt sound grout

MAPEI's safety data sheet for Keracolor S sanded grout (version 10, March 26, 2026) gives "pH (water dispersion, 10%): 11.00." That is the grout itself, mixed in water. A cleaner at pH 10.3 is a little less alkaline than the joint, and even the Febreze version at 11.0 only matches it.

Grout makers sell stronger alkalis than this for their own grout: Custom Building Products rates its Aqua Mix Heavy-Duty Tile & Grout Cleaner at "11-12 (alkaline)" (TDS-164, March 23, 2023). Mr. Clean sits below that product on every sheet found.

The bucket is milder again. One-eighth cup is 1 fluid ounce and a gallon is 128 fluid ounces, so the floor mix is about one part Mr. Clean to 128 parts water. With 1 to 5 percent surfactant in the bottle, the bucket holds well under a tenth of a percent.

The cleaner also has none of what sealer makers ban. Aqua Mix Sealer's Choice Gold (TDS-158, March 23, 2023) says: "Do not use cleaners containing ammonia, acids or bleach. Use an appropriate TileLab® or Aqua Mix® neutral cleaner." No multi-surface sheet lists any of the three. It is alkaline, though, not neutral, which matters for sealed grout.

What the label says to do, and the line that matters

Mr. Clean's product page for the Ocean scent gives two methods. They are worth reading word for word:

  • Floors and dilute cleaning: "Mix 1/8 cup per 1 gallon (1/2 bucket) of water. Usually no need to rinse."
  • Tough jobs: "Pour directly on tough soil or on sponge. Wipe and rinse."

The page lists "linoleum, tile & hardwood floors" among its uses. For wood it adds: "Use diluted only." And it names what to avoid: "Not recommended for carpets, copper or aluminum surfaces."

The two methods are the whole answer for grout. Mopping a tile floor is the first case, and the weak mix, at about 1 to 128, leaves little behind, which is why the label says "usually" no rinse. Dark grout lines are the second case: tough soil, worked with a sponge. There the label tells you to rinse, with no "usually."

The sticky floor: what the complaints are really about

Sticky tile after mopping is a common complaint with any floor cleaner, and the cause is not the brand. It is cleaner left on the floor.

Zerorez, a carpet and tile cleaning chain, puts it this way: "Your mop may not be able to lift all the cleaning solution off of the floor, which means it is drying on the surface of your floor and creating a film that feels sticky and keeps your floors looking dull." Its first suspect is too much cleaner: "it could be that you are oversaturating your floors with the cleaning solution you are using." Hunker's guide to sticky tile floors (Cathy Habas, updated June 16, 2020) says the same: "regardless of your chosen cleaner, it's imperative to rinse it off with clean water so that the cleaner doesn't leave a sticky residue when it dries."

Tile makers agree, and Daltile's care guide says glazed tile "can be cleaned with clear water and/or a pH neutral liquid cleaner (soapless). Follow with a clear water rinse and wipe dry to prevent film formation."

So there are three ways to get a sticky floor with Mr. Clean: a heavy pour in the bucket, well past 1/8 cup; neat cleaner on the joints with no rinse after; or one bucket of water used for the whole house, so the mop spreads soil instead of lifting it.

Grout catches all three. Joints are usually a little lower than the tile face, so liquid runs off the tile and sits in them. Cement grout is porous and soaks some of that liquid in, and when the water dries, the cleaner and the soil stay behind. Grout porosity and absorption explains why the joint drinks it, and cleaning floor grout covers the rinse and pickup that fixes it.

If the floor turned sticky right after someone sealed the grout, look there first. Sealer haze and sticky sealer covers that case.

A worked case: dark joints in a bathroom traffic lane

Take a bathroom floor of glazed porcelain tile with light gray cement grout, and suppose the grout was never sealed. The joints in front of the vanity have gone darker than the rest, and the bottle under the sink is Mr. Clean with Febreze Meadows & Rain.

Start with the tile. Glazed porcelain is "tile," and the label lists tile floors among its uses. Daltile says sealing is not recommended for its glazed ceramic or porcelain tile, so there is no tile sealer to worry about.

Next, the chemistry. The 2015 Febreze sheet gives pH 11.0 and no hazardous ingredients, and the grout is about 11 itself. The cleaner has no acid to dissolve the joint and no bleach to fade it.

Then the method. Dark joints are "tough soil," so the label's second method applies. Pour a little Mr. Clean on a damp sponge and work it along the dark joints, with a nylon grout brush where the sponge rides over the low spots. Then rinse with clean water and pick it up with a towel or wet vacuum. That is the label's "Wipe and rinse."

After that, the routine. Mop weekly with 1/8 cup in a gallon of warm water, and swap the water when it turns gray. Every few weeks, run plain water and a brush along the traffic lane to keep the joints from filling back up.

Change one fact, though, and the answer changes. If the doorway has a metal edge trim, it may be aluminum, which the label rules out, so keep the neat cleaner off it and rinse any splash. If the tile were honed marble, Mr. Clean would be the wrong cleaner before the grout came into it.

Why Mr. Clean's own grout page skips the liquid

Search for Mr. Clean and grout, and the brand's own page comes up: "Take The Mess Out Of Cleaning Grout." It does not mention the liquid in its method; it recommends Mr. Clean Magic Eraser Bath, which is "powerful enough to knock out even the most-stubborn buildup on grout." Mr. Clean's ceramic tile floor page does the same thing, sending readers to Magic Eraser Extra Durable.

That makes sense for a brand that sells both, but the two work in different ways. The liquid cleans with chemistry. The Magic Eraser is melamine foam, a fine abrasive that cleans by wearing the surface, and Mr. Clean's own warnings say so. It asks you to "Test a small area with light pressure before use," and it rules out "high gloss, polished, dark" surfaces, among others.

So the liquid is the gentler first step: it cannot scratch a glaze or wear down dark grout, and an abrasive can. Use the liquid and a nylon brush first, and save the eraser for marks that survive. Can you use a Magic Eraser on grout? sorts out which grout and tile can take it.

Sealed grout: dilute for routine, neat for spots

A penetrating sealer sits inside the grout, where its job is to slow water and stains down. Sealer makers rule out three things: ammonia, acids and bleach (TDS-158). Mr. Clean has none of them, so daily mopping at 1/8 cup per gallon meets that rule.

Neat cleaner is another matter. Aqua Mix warns: "Regular use of high-alkaline cleaners will reduce sealer life" (TDS-164). It means its own pH 11 to 12 product. Neat Mr. Clean at 10.3 is below that band. The Febreze bottle at 11.0 touches its lower edge. So pour it neat on sealed joints for a spot and then rinse it off, but do not make neat use the weekly routine.

Sealers wear out over time whatever you mop with, so if a joint darkens under water a year or two after sealing, test it before blaming the cleaner. The water drop test tells you in a few minutes, and how often to seal grout covers the timing.

Epoxy grout, natural stone and metal trim

Epoxy grout. Daltile says epoxy grouts are "chemically cured and acid resistant and, as a result, do not require a sealer." The same guide adds that neither sealer nor epoxy "will guarantee against surface buildup or discoloration of the grout." It says routine grout cleaning "can be done with a daily concentrated household or commercial cleaner." Mr. Clean, diluted for use, is that kind of cleaner. See cleaning epoxy grout for stubborn film.

Natural stone. Mr. Clean's label does not ban stone, but Daltile is stricter. It says stone is "porous by nature" and that "many of the cleaners acceptable for use on ceramic tile" can harm it. It asks for cleaners "specifically designed for cleaning stone," which it calls "concentrated neutral pH cleaners." Mr. Clean at 10.3 is not neutral, so on marble, travertine, limestone or slate, use a stone cleaner. Grout for natural stone covers those joints.

Aluminum and copper. The label says "Not recommended for ... copper or aluminum surfaces." On a tile floor, that means edge trims and transition strips, which can be aluminum. Grout or caulk at Schluter trim covers how those trims are set and finished. A diluted mop passes over a trim quickly. Neat cleaner should stay off it, and any splash should be rinsed.

The Mr. Clean bathroom spray is an acid

Not every Mr. Clean bottle is the multi-surface liquid, and the 2015 sheet for Mr. Clean Disinfecting Bath Cleaner with Febreze Freshness lists citric acid at 1 to 5 percent and gives pH 3.0. That is an acid cleaner, on the other side of neutral from the liquid this page covers.

Acid is the one cleaner type the grout and tile makers here rule out. TDS-158 bans acids on its sealed grout, and Daltile says acid cleaning is not recommended for its glazed ceramic or porcelain tile. So do not use the bath spray as a routine grout cleaner, and never on sealed grout. If you do spray it near joints, rinse it off. The pH chart puts acidic bathroom sprays in the "erodes with repeated use" row for cement grout. For soap scum on shower grout, see soap scum and hard water on grout.

Mr. Clean or not: grout by grout

Mr. Clean Multi-Surface Cleaner on grout, from Mr. Clean's label, P&G's sheets and tile, grout and sealer makers' rules
Grout and tileUse Mr. Clean?Why
Cement grout, glazed ceramic or porcelain floor, routine moppingYes, 1/8 cup per gallonLabel lists tile floors; pH 10.3 to 11.0 vs grout 11.00 (P&G sheets, Keracolor S)
Dark or dirty cement grout jointsYes, neat on a sponge, then rinseLabel: "Pour directly on tough soil or on sponge. Wipe and rinse."; Daltile: rinse "to prevent film formation"
Sealed cement groutYes diluted; neat only for spotsNo ammonia, acid or bleach (TDS-158); high-alkaline cleaners shorten sealer life (TDS-164)
Epoxy groutYesAcid resistant, no sealer needed; routine cleaning with "a daily concentrated household or commercial cleaner" (Daltile)
Natural stone tileNo, use a stone cleanerDaltile: cleaners "specifically designed for cleaning stone," neutral pH
Joints beside aluminum or copper trimDiluted yes; keep neat cleaner off the metalLabel: "Not recommended for ... copper or aluminum surfaces"
Mr. Clean Disinfecting Bath Cleaner on groutNot as a grout cleanerCitric acid 1-5%, pH 3.0 (2015 sheet); acids banned on sealed grout (TDS-158)

Bottom line: Use Mr. Clean Multi-Surface Cleaner on cement or epoxy grout between glazed tile. Mop at 1/8 cup per gallon. For dirty joints, use it neat on a sponge and then rinse, as the label says. At pH 10.3 to 11.0, with no acid, bleach or ammonia, it cannot dissolve grout or break a sealer rule. Rinsing is what stops the sticky film. Keep it off stone and metal trim, and try it before the Magic Eraser.

How to clean grout with Mr. Clean

  1. Check the tile and trim. Glazed ceramic or porcelain is fine. If the tile is natural stone, stop and use a stone cleaner, and note any aluminum or copper trim.
  2. Sweep or vacuum. Grit left on the floor ends up in the joints once the water hits it.
  3. For dirty joints, go neat. Pour a little Mr. Clean on a damp sponge, or straight onto the soil, and work it into the joints with the sponge and a nylon grout brush.
  4. Rinse. Go over the joints with clean water and a clean sponge, then pick it up with a towel or wet vacuum. This is the "rinse" in "Wipe and rinse."
  5. For routine mopping, dilute. 1/8 cup (2 tablespoons) in a gallon of warm water. More cleaner is not better; it is the usual cause of a sticky floor.
  6. Change the water when it turns gray. Dirty water spreads soil into the joints.
  7. Do not mix it with other cleaners. Rinse the joints before any second product goes on them.

Grout that comes away sandy under a brush was failing before you cleaned it, and a pH 10.3 cleaner did not cause that; see soft or crumbling grout for the real causes.

Mr. Clean, Murphy Oil Soap or Swiffer?

On the pH scale, Mr. Clean sits with the mild alkaline floor cleaners most homes already own. Murphy Oil Soap is pH 10.2 to 11.0, much the same, but it is a true soap, which forms scum with hard water. Mr. Clean is a synthetic detergent, not a soap. The Swiffer WetJet liquid runs pH 5.85 to 10, but the pad has no rinse step. All three are safe on sound grout, and all three leave film if they are never rinsed.

Where this answer stops applying

This page covers the Mr. Clean multi-surface liquids on the four sheets listed, used on sound, cured cement or epoxy grout. Scents with no sheet here, including Gain Original and other current versions, were not checked; read Section 9 of yours for the pH. Mr. Clean Antibacterial Multi-Surface Cleaner, the Clean Freak spray and the Magic Eraser are separate products. So is the Disinfecting Bath Cleaner, ruled on above only as an acid. The Ocean page makes no mold or mildew claim, so this is not a mildew treatment; see grout mold and mildew. Grout younger than its cure time, recolored grout, urethane or premixed grout, and waxed or coated floors follow their makers' care sheets, not this page. The 2015 Febreze sheet lists no ingredients, so its surfactant level is not known here; its pH is.

Frequently asked questions

What is the pH of Mr. Clean Multi-Surface Cleaner?

pH 10.3 on the 2008, 2023 Lemon and 2025 Ocean sheets. The 2015 Febreze Meadows & Rain sheet gives 11.0. That is mildly alkaline, not neutral.

Will Mr. Clean damage grout?

Not sound grout, because dissolving cement grout takes an acid and the multi-surface liquid is alkaline. Cement grout itself is about pH 11, so a pH 10.3 cleaner is no stronger an alkali than the joint.

Do I need to rinse Mr. Clean off tile floors?

At the weak floor mix, the label says "Usually no need to rinse." When you use it neat on grout or tough soil, the label says "Wipe and rinse." If your floor feels sticky, rinse with clean water and use less cleaner next time.

Does Mr. Clean strip grout sealer?

Diluted, no sheet shows that it would: sealer makers ban ammonia, acids and bleach, and it has none. Aqua Mix warns that regular high-alkaline cleaning at pH 11 to 12 shortens sealer life, so keep neat use on sealed grout for spots.

Is Mr. Clean or a Magic Eraser better for grout?

Start with the liquid and a nylon brush, since it cleans with chemistry and cannot scratch. The Magic Eraser is a fine abrasive; Mr. Clean rules it out on dark, polished and high-gloss surfaces.

Can I use Mr. Clean on epoxy grout?

Yes. Epoxy grout is acid resistant and needs no sealer, and Daltile allows routine cleaning with a concentrated household cleaner. It still collects surface film, though, so rinse after neat use.

Sources and standards

Grout Atlas guidance is checked against ANSI A108/A118 and ISO 13007 requirements, the TCNA Handbook and manufacturer technical data sheets. Product formulations change, so confirm details on the current data sheet for the product you buy. Spotted an error? Report a correction.