Fusion Pro vs Prism SCG Grout: What Changed, and Patching
On this page
- What Fusion Pro and Prism SCG are
- What ANSI A118.19 is, and why it matters here
- Fusion Pro vs Prism SCG side by side
- What actually changed for the installer
- Is Prism SCG harder than Fusion Pro?
- Do Fusion Pro color numbers carry over to Prism SCG?
- Can you patch Fusion Pro joints with Prism SCG?
- A worked case: patching a Fusion Pro shower wall
- Which should you buy?
- Where this answer stops applying
- Frequently asked questions
- Sources and standards
Prism SCG is the premixed grout Custom Building Products now sells in place of Fusion Pro. It is a new formula, not a new label, and on Custom's own sheets it is tested to ANSI A118.19, the new standard for premixed grout, which Fusion Pro never claimed. A shower can take water after 72 hours, not 7 days. You can leave it up to 30 minutes before cleaning, where Fusion Pro allowed 1 to 4. The joint range (1/16 to 1/2 inch) is the same, and every Prism SCG color number was a Fusion Pro color. To patch old Fusion Pro joints, cut them out and refill with Prism SCG in the same color number, after a dried test dab.
Key takeaways
- Custom's Fusion Pro data sheet (TDS-242) is now headed "PRISM SCG," but its text still describes Fusion Pro. The real Prism SCG sheet is TDS-454, published March 10, 2024.
- Prism SCG "Exceeds ANSI A118.19," the premixed grout standard, with 28-day hardness over 1,000 psi, wet hardness over 500 psi and abrasion under 500 mm3. Fusion Pro claims only "many of the performance characteristics" of A118.7 and A118.3.
- Showers: 72 hours before intermittent water for Prism SCG, 7 days for Fusion Pro, both at 70 deg F and 50% humidity. Neither is for steam rooms, steam showers or pools.
- Prism SCG comes in gallons only. Fusion Pro also came in quarts in select colors. Every Prism SCG color number was on the Fusion Pro list; only #156 Fawn did not carry over.
- No Custom document says Prism SCG matches Fusion Pro's cured shade. Make a dried dab on a spare tile and compare it with cleaned old grout before you patch.
What Fusion Pro and Prism SCG are
Both are single-component grouts. That is Custom's name for a premixed grout: grout sold wet in a pail, ready to spread, with nothing to add. Grout is the material packed into the gaps between tiles. Bagged cement grout hardens when it reacts with the water you mix in, but a premixed grout hardens a different way. Both Custom sheets say the grout "cures by evaporation." The water dries out of it, and a plastic binder holds the sand and pigment together.
The binders are named on the sheets. Fusion Pro "Contains ethylene glycol, 2-butoxy ethanol and acrylic latex." Prism SCG contains "Silica sand, styrene-acrylic polymer, titanium dioxide, ethylene glycol, and may contain carbon black." Both are sanded and both fill joints 1/16 to 1/2 inch wide.
Stone World ran Prism SCG as a new product in January 2024. Custom's product page calls it "the NEW STANDARD in Single Component Grout" and says Custom is "taking the Prism heritage and name into the adjacent category of Pre-Mixed Grout." That heritage is Prism, Custom's bagged cement grout. Prism SCG is not that product in a pail; it is a premixed grout that borrows the name.
Did Prism SCG replace Fusion Pro? Custom's own files say so. The Fusion Pro sheet, TDS-242, is now headed "PRISM SCG" on every page, dated March 12, 2024. The text under that header still reads "Fusion Pro® the original stain proof, color perfect grout." The old Fusion Pro product address now redirects to the Designer Series page. We found no dated discontinuation notice, so this page gives no date.
What ANSI A118.19 is, and why it matters here
An ANSI standard is a published set of lab tests with pass limits. Grout makers print the one they meet on the technical data sheet (TDS), the maker's own spec sheet. For years, premixed grout had no standard of its own, so makers borrowed tests from A118.7 (cement grout) and A118.3 (epoxy) and picked which ones to report. That is exactly what the Fusion Pro sheet does: it "Meets many of the performance characteristics of ANSI A118.7 and A118.3." The site's guide to grout standards explains those older codes.
ANSI A118.19 changed that, as the American National Standard for organic premixed grouts. TILE Letter reported it as new in February 2024, alongside A108.22, a matching standard for installing premixed grout. The standard defines this kind of grout as "a ready for use, factory prepared mixture of water, polymers, aggregates, pigments and other materials."
A118.19 does not crush grout cubes the way cement grout tests do. It presses on the grout and measures the dent, a test called indentation resistance. Per a June 2025 summary in The Construction Specifier, samples are loaded at 1,000 psi after 28 days of drying. Another set dries 21 days, then soaks in water for 7 days before it is loaded at 500 psi. The dent may be no deeper than 1.14 mm (0.045 inch). That is what Prism SCG's "Hardness at 28 days >1000 psi" and "Wet Hardness >500 psi" lines refer to. The wet test, after a week under water, is the one that matters for a shower. Fusion Pro's sheet has no wet test at all.
Fusion Pro vs Prism SCG side by side
Every row below comes from the two sheets: TDS-242 (Fusion Pro, the copy dated March 12, 2024) and TDS-454 (Prism SCG, March 10, 2024).
| Item | Fusion Pro | Prism SCG |
|---|---|---|
| Standard claimed | "Many of the performance characteristics" of A118.7 and A118.3 | Meets A118.19; key features say "Exceeds"; plus many A118.7 and A118.3 characteristics |
| Hardness | Shore D 76 (ASTM D2240) | Over 1,000 psi at 28 days; wet over 500 psi (A118.19) |
| Abrasion | Not listed | Under 500 mm3 |
| Stain test (CTIOA T-72 modified) | 0.5 to 1 | 0.5 to 1.5 |
| Floor test (ASTM C627) | Not listed | Heavy Duty |
| Joint width | 1/16 to 1/2 inch | 1/16 to 1/2 inch |
| Spread before cleaning | 1 to 4 minutes, about 10 sq ft | 10 to 15 minutes, or 60 to 100 sq ft; up to 30 minutes to clean |
| Light traffic | 24 hours | 24 hours |
| Shower water | 7 days | 72 hours |
| Install temperature | 50 to 90 deg F | 50 to 90 deg F |
| Excluded | Steam rooms; submerged (pools, spas, fountains) | Steam rooms or steam showers; constant submersion (pools, water features) |
| Exterior | "Exterior and interior applications" | Interior and "most exterior" |
| Sealing | Not necessary; no solvent sealers | Not necessary; no solvent sealers or enhancers |
| Sizes | 1 gallon; 1 quart in select colors | 1 gallon only |
| Colors | "40 standard colors"; the gallon table lists 41, including #156 Fawn | 40 standard, all from the Fusion Pro list |
The stain row is a range on both sheets. The sheets do not explain the scale, and the ranges overlap, so this page draws no ruling from it. The gallon coverage charts are the same on both sheets, figure for figure, so a gallon covers the same area of either.
What actually changed for the installer
Working time. This is the change you feel first: Fusion Pro says to "Only spread for 1-4 minutes before cleaning grout off the tile surface," in about 10 sq ft patches. It warns "Do not apply or clean up this grout as typically done with cement or epoxy grout." Prism SCG lets you fill joints for 10 to 15 minutes, or 60 to 100 sq ft, and "can have up to 30 minutes working time for cleaning." That holds in mild conditions on tile that is not porous.
Shower cure. Fusion Pro needs "7 days at 70° F (21° C) and 50% relative humidity before intermittent water exposure (such as a shower enclosure)." Prism SCG needs 72 hours under the same conditions, and both sheets say colder and more humid air slows the cure. Grout cure time compares these with cement and epoxy grouts.
Pre-wetting. Fusion Pro says to "Lightly dampen tile surface before spreading" every time. Prism SCG says the same and then adds: "Glazed or impervious tile do not require pre-wetting." Neither allows puddles.
Haze. If residue dries on the tile, Fusion Pro reaches for a haze cleaner after 2 hours. Prism SCG says to wait 2 to 3 hours, wipe with clean water, and use a cleaner only if streaks remain after 72 hours. How to remove grout haze covers the products both sheets name.
New limits on Prism SCG. The Prism SCG sheet adds rules Fusion Pro did not spell out. In-service surface temperature must stay under 160 deg F, and it is not for slabs giving off more than 5 lbs of moisture or above 85% relative humidity. Fusion Pro said only "high moisture emission rates." Mirror tile also joins the list of surfaces to test first.
Two Fusion Pro uses not repeated. Fusion Pro listed "Exterior and interior applications" with no qualifier. Prism SCG says interior and "most exterior" and points to its limits. Fusion Pro's suitable tile list also named "cement body tile," which Prism SCG's list does not. Its list names ceramic, mosaic, quarry, porcelain, glass, polished stone, terrazzo and groutable vinyl tile. For cement tile, ask Custom before you use it.
Marketing words. Fusion Pro was sold as "stain proof." Prism SCG is "highly stain-resistant." Both say "No efflorescence," the white powder that cement grout can bloom. Neither grout contains cement.
Is Prism SCG harder than Fusion Pro?
Two views circulate. One installer newsletter, titled "Fusion Pro is on its way out," says single-component grouts "tend to be a bit softer and they don't hold up to abuse very well." The writer would still not use them on shower floors, and had not yet used Prism SCG. The other view is Custom's: Prism SCG is the "NEW STANDARD."
Fusion Pro's hardness is a Shore D reading of 76. Prism SCG's is a pass at A118.19's 1,000 psi indentation load. These are different tests with different units, and no sheet converts one into the other, so this page does not claim Prism SCG is harder by any amount.
What the sheets do settle is this. Prism SCG has passed a standard built for premixed grout, with a wet hardness check and an abrasion limit, and it rates "Heavy Duty" on the ASTM C627 floor test. Fusion Pro reported none of those. The softness worry was formed on grouts never held to a premixed standard. Prism SCG is, and the newsletter was written before its writer had tried it.
Do Fusion Pro color numbers carry over to Prism SCG?
All but one do. Read side by side, the Fusion Pro table lists 41 colors in gallon pails and the Prism SCG table lists 40. Every Prism SCG color is on the Fusion Pro list under the same number and name. The sell sheet confirms all 40 come in the gallon pail. The one Fusion Pro color missing from Prism SCG is #156 Fawn.
Even the item codes follow one pattern: Fusion Pro #381 Bright White is FP3811-2T. Prism SCG #381 Bright White is PSCG3811-2T.
The shade is a separate question. Both sheets say "Final installed shade may vary with the tile type, color and porosity as well as jobsite conditions and finishing techniques." No Custom document we found says a Prism SCG color cures to the same shade as the Fusion Pro color with that number. The binder changed, so treat the number as the closest match Custom sells, not a promise. Checking is quick. The Prism SCG sheet says the wet color "is not representative of the final result." It says to place "a small dab of grout on the tile and allow to dry (or use hair dryer)." That gives a dry sample in minutes, not days.
Can you patch Fusion Pro joints with Prism SCG?
Yes, by cutting out the bad joints and refilling them. Prism SCG is the grout Custom sells for that job now. The Prism SCG sheet sets the material rules, the site's spot grout repair guide sets the cutting rules, and the dried dab decides the color.
- Cut, do not skim. The Prism SCG sheet says "Tiled surface and joints must be clean" and "Ensure all grout joints are completely full." It gives no minimum depth and no rule for going over old grout. So cut out at least two thirds of the joint depth, as spot grout repair explains. Grouting over old grout covers why a thin skim fails.
- Let it dry, do not keep it damp. Cement grout patches are kept damp to cure, but Prism SCG "cures by evaporation," so it needs air. Cover it only after 24 hours, and then only with something breathable such as kraft paper.
- Corners get caulk. Both sheets say the grout is "Not for use in movement joints or changes of plane." Where a wall meets a tub, tray or another wall, use the caulk or silicone the sheet names. See caulk vs grout in movement joints.
- No solvent products. If you seal nearby stone after patching, the sheet says to use a water-based sealer and wipe it off the joints. "Do not use solvent-based sealers or enhancers after Prism® SCG is installed."
Old Fusion Pro that was later recolored is a different case: match the colorant, not the original bag color. Matching existing grout color covers cleaning the old joint first so you compare against its real color.
A worked case: patching a Fusion Pro shower wall
Take a shower wall tiled with 4-1/4 inch glazed ceramic and 1/8 inch joints. The grout is Fusion Pro #381 Bright White, named on an old pail lid. Suppose six joints around a soap niche have cracked, and the store has no Fusion Pro, only Prism SCG.
Start with the color. #381 Bright White is on the Prism SCG list, so the pail to buy is Prism SCG #381, which comes only in a gallon. On the sheet's coverage chart, a gallon fills about 110 sq ft of 4-1/4 inch tile at 1/8 inch joints. Keep the rest from freezing, as the sheet says.
Next, the sample. Scrub a few inches of old grout clean and let it dry. Then put a dab of Prism SCG on a spare glazed tile and dry it with a hair dryer, as the sheet allows. Hold it beside the clean old joint in the shower's own light. If it is close, go ahead. If it is clearly off, a patch will show, and the fix is a grout colorant over the whole wall, or regrouting it.
Then the joints. Cut the cracked grout out to at least two thirds of the joint depth, and stop at the joints where the niche meets the wall, since a change of plane takes caulk. Vacuum out the dust. Because the tile is glazed, the Prism SCG sheet does not require pre-wetting. Press the grout in with a float held at 45 degrees, then scrape the face at 90 degrees. Sponge lightly, then wipe with a damp microfiber cloth.
Last, the wait. At 70 deg F and 50% humidity, the sheet allows the shower back in use after 72 hours. In a cold or steamy bathroom, give it longer. Had the same wall been patched with Fusion Pro, its sheet would ask for 7 days.
Change one fact and the answer shifts. If the old color were #156 Fawn, Prism SCG has no such color, and only a dried dab of a nearby color will tell if any is close enough. If the joints were in a steam shower, neither grout belongs there at all.
Which should you buy?
New tile: Prism SCG. It is the one Custom sells, it is tested to the premixed standard, and the shower is usable 4 days sooner. Only two Fusion Pro uses are missing from the Prism SCG sheet: exterior work without the "most" qualifier, and cement body tile.
Patching old Fusion Pro: Prism SCG in the same color number, after a dried dab. For #156 Fawn, test the nearest colors.
A pail of Fusion Pro still on the shelf: it is the same product its sheet describes. Use it to its own rules, including the 1 to 4 minute spread and the 7 day shower wait.
Steam showers, pools and fountains: neither, since both sheets exclude them. See steam shower grout and pool grout.
Pebble and irregular stone with joints over 1/2 inch wide or deep: neither, per both sheets. See grout for pebble tile.
For how Prism SCG sits beside cement and epoxy grouts, see premixed vs powder grout and grout product lines compared.
Bottom line: Prism SCG is Custom's new premixed grout in Fusion Pro's place, not Fusion Pro renamed. It meets ANSI A118.19, which Fusion Pro never claimed, takes water in a shower after 72 hours instead of 7 days, and can wait up to 30 minutes for cleanup where Fusion Pro allowed 1 to 4. Same joints, same color numbers except #156 Fawn. To patch Fusion Pro, cut the joints out, refill with Prism SCG in the same number, and trust a dried dab, not the label.
Where this answer stops applying
This page compares two Custom data sheets as fetched on November 15, 2026: TDS-242 for Fusion Pro (dated March 12, 2024, under a Prism SCG header) and TDS-454 for Prism SCG (March 10, 2024). It does not cover the Fusion Pro Designer Series colors, which have their own sheet, or Prism cement grout, which is a different product. Custom has published no test of Prism SCG over or beside cured Fusion Pro, so the patching steps rest on Prism SCG's own rules and the site's repair method, not on a compatibility test. The hardness figures come from different tests and cannot be ranked against each other. The A118.19 test details are from trade press summaries, not the standard itself. This page does not interpret Custom's system warranty. Color lists and sheets change, so check the current color card and TDS where you buy. This page does not compare prices.
Frequently asked questions
Is Fusion Pro discontinued?
Custom now serves its Fusion Pro data sheet under a "PRISM SCG" header and promotes Prism SCG as its single-component grout. We found no dated discontinuation notice, so stores may still carry Fusion Pro.
Is Prism SCG the same as Fusion Pro?
No. The ingredients listed differ (styrene-acrylic polymer versus acrylic latex), it meets ANSI A118.19, it can wait up to 30 minutes before cleanup where Fusion Pro allowed 1 to 4, and a shower can take water after 72 hours instead of 7 days.
Is Prism SCG the same as Prism grout?
No. Prism is Custom's bagged cement grout, while Prism SCG is a premixed grout in a pail that shares the name.
Can Prism SCG be used in a steam shower?
No. TDS-454 says it is "Not for use in constant submersion (pools, water features), steam rooms or steam showers." Fusion Pro's sheet excluded steam rooms too.
How long before I can shower on Prism SCG?
72 hours at 70 deg F and 50% relative humidity, per the sheet, and cooler or more humid air takes longer. Light foot traffic is allowed after 24 hours.
Can I put Prism SCG over old Fusion Pro without removing it?
The sheet gives no rule for going over old grout and says joints must be clean and completely full. Cut the old grout out to at least two thirds of the joint depth and refill.
Sources and standards
- Custom Building Products, Prism SCG, TDS-454 (published March 10, 2024): standards, technical chart, limits, application, curing, sealing, 40-color list, coverage
- Custom Building Products, TDS-242, headed "PRISM SCG," describing Fusion Pro Single Component Grout (published March 12, 2024): standards, Shore D, limits, application, curing, color list
- Custom Building Products, Prism SCG product page
- Custom Building Products, Prism SCG sell sheet SS216 (3/26 revision)
- Stone World, Prism SCG from Custom Building Products (January 17, 2024)
- Will White, TILE Letter, New ANSI Pre-Mixed Grout Standard (February 1, 2024): A118.19 and A108.22, indentation resistance
- Howard Jancy, The Construction Specifier, From mix to fix: The benefits of single-component grout (June 5, 2025): A118.19 definition and indentation limits
- DIYTileGuy newsletter, Fusion Pro is on its way out: what about its replacement? (installer opinion)
- ANSI A118.19, Organic Premixed Grouts for Installation of Ceramic Tile, and ANSI A108.22, Installation of Pre-Mixed Grout in Tilework, as cited on TDS-454 and in the trade press above
Grout Atlas guidance is checked against ANSI A108/A118 and ISO 13007 requirements, the TCNA Handbook and manufacturer technical data sheets. Product formulations change, so confirm details on the current data sheet for the product you buy. Spotted an error? Report a correction.